If the ammeter reading in Diagram 1 is zero, it indicates that there is no current flowing through the circuit. This could be due to an open circuit, meaning there is a break or disconnection somewhere in the circuit path. Other possible reasons include a faulty ammeter or components that are not functioning properly, such as a burned-out fuse or a disconnected power source. To diagnose the issue, check for continuity and ensure all components are securely connected and operational.
In a series circuit, the current is the same throughout all components. Therefore, both ammeter 1 and ammeter 2 will read the same current, as they are measuring the same flow of electrons in the circuit. The readings on both ammeters will be equal, so neither will have a bigger reading. The voltage drop across the lamps may differ, but that does not affect the ammeter readings.
If one bulb in a series circuit blows out, the circuit becomes open, and the current stops flowing. As a result, the reading on the ammeter will drop to zero since there is no current passing through the circuit. In a parallel circuit, if one bulb blows out, the current may decrease slightly due to the change in total resistance, but the ammeter will still show a reading corresponding to the remaining bulbs in operation.
If you're connecting it properly, then I would have to guess that the multimeter is defective.
Assuming the new lamp is in series, the ammeter reading falls because the total resistance has increased. By how much depends on how the lamp resistance depends on voltage. If the lamp is added in parallel to the first, then the ammeter reading doubles.
i=v/r can be used to it
If the resistor is removed from the circuit, the total resistance in the circuit decreases. This causes the total current in the circuit to increase, which would result in an increase in the ammeter reading.
An ammeter reads the current that is flowing through a branch of a circuit. If there is a break within that same branch of the circuit, current will not be able to flow through that branch of the circuit as it forms an incomplete loop, so the ammeter will read 0 A of current. If there is a break in a circuit in a branch that is not connected to the ammeter however, the ammeter will give a higher reading of the current. This is assuming that the break in the other branch does not short out the branch with the ammeter attached, and that the circuit can still form a complete loop without that branch.
An open switch in a circuit will stop all current flow so the ammeter should read zero amps.
In a series circuit, the current is the same throughout all components. Therefore, both ammeter 1 and ammeter 2 will read the same current, as they are measuring the same flow of electrons in the circuit. The readings on both ammeters will be equal, so neither will have a bigger reading. The voltage drop across the lamps may differ, but that does not affect the ammeter readings.
The voltage remains the same across the circuit as it is a parallel connection. So, the current across the upper half of the circuit where the ammeter is connected is calculated as I = V/R = 12.04 (total voltage)/12 (Resistance R1) = 1 A. Hence, the ammeter will read 1 A.
If one bulb in a series circuit blows out, the circuit becomes open, and the current stops flowing. As a result, the reading on the ammeter will drop to zero since there is no current passing through the circuit. In a parallel circuit, if one bulb blows out, the current may decrease slightly due to the change in total resistance, but the ammeter will still show a reading corresponding to the remaining bulbs in operation.
An ammeter is the instrument used to measure current in an electric circuit. It is connected in series in the circuit and provides a reading of the amount of electric current flowing through it.
Connect ammeter in series and voltmeter in parallel to the circuit
The strength of an electric current is measured in amperes (A) using an ammeter. An ammeter is a device that is connected in series in a circuit to measure the flow of current. The higher the current flowing through a circuit, the higher the amperage reading on the ammeter.
An ideal ammeter is a device that measures electric current and has zero resistance, producing no voltage drop when connected in a circuit. This ensures that the current being measured is not affected by the presence of the ammeter itself, providing an accurate reading of the current flowing through the circuit.
The decrease of light intensity on an LDR will cause the resistance of the LDR to increase, which will result in a decrease in current flow through the circuit. As a result, the ammeter reading will decrease.
If you're connecting it properly, then I would have to guess that the multimeter is defective.