0
In what condition does a motor gets burnt out when running at rated load?
Wiki User
∙ 15y ago
If overload is not the cause, then high temperature could be caused by blocking the cooling of the motor.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
What is motor rated torque?
It is the twisting force that a motor can produce when it is running.
What causes speed drop in motor?
1) If current, at 'on load' condition, reach or cross its rated value, then the speed of the motor will be decreased. 2) If there is any voltage droop occurs in the incoming supply then the speed of the motor will be decreased.
What does LRA mean in electrical terms?
Locked rotor amperage is the amperage the motor draws when the voltage is first applied to the motor and the rotor has not started to turn. This amperage is usually up to 300% of the motors running amperage. Once the rotor starts to turn the motor generates a back EMF (electro motive force) that opposes the high inrush current. This back EMF drives the amperage down until the motor gets up to its rated speed at which time the motor amperage will be at its run amperage.
What are the calculation for overload relay for three phase motor?
If a motor 3 phase or single phase goes above the full load amps that is on the nameplate of the motor then it is in overload condition. This is usually caused by trying to drive machinery with less horsepower that the manufacturer recommends To protect the motor from this condition overload heaters are put in series with the supply voltage and the motor leads. If the current from the motor draws more that the motor's nameplate FLA then the overload heater opens the supply voltage through use of a motor contactor. The contactor can not be closed again until the motor overload heaters cool down and by the same token the motor gets a chance to cool down. This condition is rectified by either using a bigger HP rated motor or lowering the load on the machinery that the motor is driving.
How are motor start capacitors rated?
Motor start capacitors are rated with two main values. One is capacitance in micro farads and the other is in voltage.
What is motor rated torque?
It is the twisting force that a motor can produce when it is running.
What will happen if you stop the rotor and supply is continue in induction motor?
This is done under blocker rotor test of induction motor in which the rotor of the motor is stopped by some external mechanical means and the supply is increased slowly from the autotrasformer until the rated motor current is reached and the V , I ,W readings are taken . As the rated current flows the winding temperature increases but upto rated current this temperature rise is within the safe limits . In the blocked rotor condition the rated current is achieved at around 20-25% of the rated supply voltage . If we further increase the voltage then the current flowing is more than it's rated or permissible value so windings get dengerously hot and they get burnt or damaged .
What are the ratings and certificates for Burnt In - 1920?
Burnt In - 1920 is rated/received certificates of: UK:A
What are the ratings and certificates for Burnt Wings - 1916?
Burnt Wings - 1916 is rated/received certificates of: UK:U
What causes speed drop in motor?
1) If current, at 'on load' condition, reach or cross its rated value, then the speed of the motor will be decreased. 2) If there is any voltage droop occurs in the incoming supply then the speed of the motor will be decreased.
What does LRA mean in electrical terms?
Locked rotor amperage is the amperage the motor draws when the voltage is first applied to the motor and the rotor has not started to turn. This amperage is usually up to 300% of the motors running amperage. Once the rotor starts to turn the motor generates a back EMF (electro motive force) that opposes the high inrush current. This back EMF drives the amperage down until the motor gets up to its rated speed at which time the motor amperage will be at its run amperage.
Why is it necessary to keep the speed of a generator or motor to the rated value?
I'm not entirely positive, but increasing or changing the conserved rated speed of a generator or motor might generate high and intense heating, waste large amounts of power, and possibly will cease to produce the necessary torque to keep running.
What is the solution for running three phase induction motor at voltage less than its rated voltage to drive full load?
The solution to this problem is to get the same size motor in HP at the correct voltage. This way the motor can correctly drive the connected full load without tripping the motor protection.
What is the difference between full load amps and running load amps?
Full load amps is the maximum rated amps that the motor should draw according to its nameplate rating. Running load amps is the actual amperage the motor is drawing at that point in time when the test is taken. Some motor loads vary depending on if the load is cyclic. The reading on this type of motor would be from no load amps to full load amps.
What is the common application for capacitors in electric motors?
There are 2 types of capacitor including starting capacitor and running capacitor running capacitor are used to improve the power factor of motor. starting capacitor used in split phase induction motor . starting capacitor may isolate from motor,s starting winding through of centrifugal switch after getting motor 90% of it,s rated speed.
What are the best rated running gloves?
For men the best rated running gloves are Nike Convertible Running Mitten Gloves. And for women the best running gloves are Nike Lady Lightweight Running Gloves.
What are the calculation for overload relay for three phase motor?
If a motor 3 phase or single phase goes above the full load amps that is on the nameplate of the motor then it is in overload condition. This is usually caused by trying to drive machinery with less horsepower that the manufacturer recommends To protect the motor from this condition overload heaters are put in series with the supply voltage and the motor leads. If the current from the motor draws more that the motor's nameplate FLA then the overload heater opens the supply voltage through use of a motor contactor. The contactor can not be closed again until the motor overload heaters cool down and by the same token the motor gets a chance to cool down. This condition is rectified by either using a bigger HP rated motor or lowering the load on the machinery that the motor is driving.
