0
What else can I help you with?
What is a recifier?
An electrical device that converts alternating current into direct current is a rectifier. Diodes, which pass only current going one direction, are a type of rectifier. Most power supplies for electronic equipment contain rectifiers along with other components to "clean" the DC power output.
What is the significance of the cathode being negative in an electrical circuit?
The significance of the cathode being negative in an electrical circuit is that it attracts positively charged ions or electrons, allowing for the flow of electric current in the circuit. This helps to control the direction of the current and ensures that the circuit functions properly.
A path that allows only one route for an electric current is called a?
A path that allows only one route for an electric current is called a series circuit. In a series circuit, all components are connected in a single loop so that the current passes through each component in sequence.
What is the function of the negative anode in an electrical circuit?
The negative anode in an electrical circuit serves as the point where electrons flow out of the circuit, completing the electrical circuit and allowing for the flow of electric current.
A circuit that has only one path for electricity to flow through?
A circuit with only one path for electricity to flow through is called a series circuit. In a series circuit, the components are connected end-to-end, so the current flows through each component in sequence. If one component fails, the entire circuit will be broken.
What has the greater current in the diodes bridge rectifier circuit or full-wave rectifier circuit?
They both have the same current.
What is the effect of an RL circuit in half wave rectifier?
The effect of an RL circuit in half wave rectifier is that the voltage output wave forms for current and voltage will be modified .
Guyz how much voltdrop do you expect to get when measuring across 1 of the fwd biased Si diodes when the circuit is a fullwave bridge rectifier if supplied with 12Vac load being 3673 ohms?
A; engineers assume .6 to .8 volts depending on current flow however Boltzmann constant can be applied if the current is fixed otherwise back to assuming.
What converts an alternating current to diredt current?
Alternating Current can be converted to Direct Current by using a DC Converter which contain a Bridge Circuit , a Capacitor and if needed a Transformer.CommentA 'DC converter' is normally called a rectifier.
Which electronics circuit gives unidirectional current or wave form?
A rectifier circuit produces a unidirectional wave form.
Can a rectifier work either way?
if you are looking for the direction of rectifier than Yes. the rectifier convert the alternating current to one directional Direct current. It work as short circuit on the case of forward biasing and work as open circuit on the reverse biasing so it can work only in one direction.
Why capacitor is used in circuit board?
use as coupling in some circuts and and as a filter in rectifier circuit. use as DC current blocking.
What is full wave bridge rectifier?
A: This type of rectifier circuit will conduct current trough a load both times during the AC positive and negative cycle
How do you determine the size of acapacitor in a rectifier circuit?
ANSWER In rectifiers for power supplies, the capacitor size is determined by the allowable ripple on the output. This can be determined by the rate at which the capacitor is drained. Specifically, this rate is the current drawn from the capacitor. Assume a half wave rectifier made from four diodes. For part of the cycle, the output current is supplied by the rectifier diode. This is also when the capacitor is charged. While the rectifier is not supplying current -- when the input waveform has dropped below the output voltage -- the capacitor must supply the current. Then, as the input waveform rises above the capacitor voltage, the rectifier supplies the current to charge the capacitor and the output circuit.
What does the current equals in a bridge rectifier?
In a bridge rectifier, the current output is the same as the input AC current during the positive half-cycle of the AC waveform. However, during the negative half-cycle, the diodes in the bridge configuration allow current to flow in the same direction, effectively converting AC to DC. The output current can be influenced by the load connected to the rectifier and may vary based on the input voltage and the characteristics of the rectifier circuit.
Why full eave rectifier rectifies negative half cycle?
the rectifier is Mainly used to convert the Ac current into DC current .In rectifier there are two diodes or (4 Diode In full wave bridge rectifier )are use is to conduct the current one is connected in forward bias(i.eD1) and the other is connected in reveres bias(i.eD2). As we know that the diode is conduct the current throw it When it is connected in forward bias . now when the voltage is applied to the circuit the the AC Current is start to flow throw circuit and in Positive half cycle of Ac current the Diode is Allow the current Pass throw it and during the Negative half cycle the Diode D2 is allow the current pass throw it and in these way the rectifier rectifies positive As Well As the negative half cycle
What does the out put wave form looks in a rectifier?
A rectifier allows current to flow only in one direction. In a half-wave rectifier circuit, an input wave which oscillates between positive and negative, will 'pass through' the positive portion of the wave, and when the input is negative will output zero. A full-wave rectifier circuit, is commonly configured with 4 rectifier diodes, which allow a positive wave to output when the input wave is negative.
