ISO 46 and AW 46 refer to hydraulic fluids with a viscosity grade of 46 centistokes at 40°C, but they are not exactly the same. ISO 46 is a designation under the International Organization for Standardization (ISO) that specifies the viscosity grade, while AW (Anti-Wear) 46 indicates that the fluid contains anti-wear additives, making it suitable for hydraulic systems. While both may have similar viscosities, the AW designation specifies additional performance characteristics related to wear protection.
the amount u put aw aw yea lick
Is it a central water heater or a local point of use water heater?With the centralized system:Hot water pipes are more susceptible to corrosion then cold water pipes, the hot water accelerates the build up of rust. If you have galvanized piping, that can be a major source of slow water.The hot water heater may also have problems which reduce the rate that water can get into the tank and from there on into the piping system. You might insure that the valves on the hot water heater and along the flow path are all fully opened.With a point of use system, it may be that there is a control valve that won't allow the water to flow unless it is a certain temperature. If it is taking longer to heat the water, it could slow down the flow considerably.When the hot side pressure is bad in all of the house it is going to be a problem with the hot water heater outlet usually. If it is just bad at one location especially when it is the shower and your shower is a single handle unit, it is the cartridge in the valve body. It is a very common problem with Moen valves as well. Simply replace cartridge by removing trim then cartridge and install new one. They should carry your part at home depot. You will be back in business.If it is all over the house try replacing the hot side nipple and supply line coming out of heater,that will usually take care of it. If not it could be build up in piping and you might need a repipe.http://aw-sons.com/slow-hot-water-flow-in-shower/
Several pieces of information are missing from the question, so this answer makes several assumptions; 480 delta, 0.92 power factor, and 0.95 efficiency.First and foremost, consult the name plate on the motor and the specifications as well. That should be the primary answer.10 horsepower is 7.5 KW. (746 watts per horsepower)7.5 KW divided by 0.92 PF divided by 0.95 EFF is 8.5 KVA.8.5 KVA divided by 480 V is 17.8 A.17.8 A divided by 3 is 5.9 A per winding.5.9 A per winding times 1.732 (30.5) is 10.3 A per phase.10.3 A per phase times 1.25 running factor is 12.8 A breaker size.You probably want a 15 A three phase breaker.Starting current could be as high as 51 A, four times run current, but the breaker should handle the transient. This can be mitigated by a wye-delta starter configuration, depending on the motor. Back to the specifications. Again, consult them first.
AW 46
For the gearbox hydraulic unit of a 454 International tractor, it is recommended to use a high-quality hydraulic oil that meets the ISO 46 specification. Common options include hydraulic oils such as AW 46 or equivalent. Always refer to the owner's manual for specific recommendations, as it may specify particular brands or formulations suitable for optimal performance.
For the Mustang 2060 skid steer, it is recommended to use a high-quality hydraulic oil that meets the specifications of ISO 46 or AW 46 viscosity grades. Look for hydraulic fluids that are anti-wear, rust-inhibiting, and have good thermal stability. Always consult the operator's manual for specific recommendations and ensure the oil meets any manufacturer's standards. Regularly check the oil level and condition to maintain optimal performance.
The primary type of hydraulic oil used in case backhoes is 10wt or AW-46. Each type has specific properties for longevity, performance, and resistance to harsh temperatures.
To fill the hydraulic oil in a Case 580K backhoe, locate the hydraulic reservoir, which is typically found near the rear of the machine. Use a high-quality hydraulic oil that meets the manufacturer's specifications, usually AW 32 or ISO 46 hydraulic fluid. Ensure the oil is clean and free of contaminants before filling, and check the dipstick to ensure the correct level after filling. Always refer to the operator's manual for specific oil recommendations and capacities.
For a Case 430 tractor, it is generally recommended to use a hydraulic oil with a viscosity grade of ISO 46 or an equivalent AW (Anti-Wear) hydraulic fluid. The specific oil type may vary based on operating conditions and temperatures, so it's always best to consult the tractor's owner's manual for manufacturer specifications. Additionally, using a high-quality oil that meets the required standards can help ensure optimal performance and longevity of the hydraulic system.
Bad Boy Mowers typically recommend using a high-quality hydraulic fluid that meets the specifications of ISO 32 or AW 32 hydraulic oil. It's essential to use the right fluid to ensure optimal performance and longevity of the mower's hydraulic system. Always check the owner's manual for specific recommendations and guidelines for your model.
aw32
The Ford 2310 typically uses a hydraulic fluid that meets the specifications of either ISO 32 or AW 32 hydraulic oil. It's important to check the owner's manual for the specific requirements and recommendations for your model, as well as to ensure the fluid meets the necessary standards for optimal performance. Always use fluids that are compatible with the tractor's hydraulic system to avoid damage.
For the hydraulic pump of a Cub Cadet, it's generally recommended to use a high-quality hydraulic fluid that meets the specifications of ISO 32 or AW (Anti-Wear) hydraulic oil. Look for fluids specifically designed for hydraulic systems to ensure optimal performance and protection. Always check your owner's manual for any specific recommendations or requirements for your model.
Yes, AW 68 hydraulic oil can be used in a Case backhoe, provided it meets the manufacturer's specifications for hydraulic fluid. AW 68 is a common type of hydraulic oil with good viscosity characteristics for many hydraulic systems. However, it's essential to check the backhoe's owner manual or consult with the manufacturer to ensure compatibility and avoid any potential issues. Always consider factors like temperature and operational conditions when selecting hydraulic oil.
AW-32