0
What else can I help you with?
I'm using a 18.5 volts 3.5 amps charger to charge a 12 volts battery I want to reduce voltage to 15 volts and current to about or a little less than 2 amps How to reduce charging current and voltage?
You need a regulator.
What is PIV.Why PIV of a semiconductor diode is important?
peak inverse voltage... piv of semiconductor is impoetant bcz we need to know after a peak voltage the diode get breakdown or damaged... so we need to know the peak voltage. piv is a point which withstands the maximum reverse biased voltage. after which the diode get damaged.
What materials do you need to make a board game?
i made a fun rpg with a piece of paper pen little marbles and a little notebook to keep track of my stats
Four 50 ohms are connected in series calculate the current in the circuit?
The series resistance is 4 x 50 = 200 Ohms. You would need additional information to get the current; usually this is calculated from the voltage. current = voltage / resistance.The series resistance is 4 x 50 = 200 Ohms. You would need additional information to get the current; usually this is calculated from the voltage. current = voltage / resistance.The series resistance is 4 x 50 = 200 Ohms. You would need additional information to get the current; usually this is calculated from the voltage. current = voltage / resistance.The series resistance is 4 x 50 = 200 Ohms. You would need additional information to get the current; usually this is calculated from the voltage. current = voltage / resistance.
What should be the secondary voltage of a transformer needed in a rectifier circuit if the required DC voltage is 6 volts using a?
A little more than 6 volts RMS, or 17 volts peak to peak (can get -6 and +6 voltage this way using a full wave rectifier). The voltage will depend strongly on your design - are you using circuitry that clamps the output voltage to a specific value (you should!). If you are doing this, I would find the cheapest transformer that meets the current capacity you need that has an output near the 6 volts you want.
How many amps in 3.5 horsepower?
You need to know the voltage as well before the conversion can be made.
What is the need of voltage regulator?
To regulate the voltage
Do I need a voltage converter for the UK?
Yes, if your electronic devices are not compatible with the UK's voltage of 230V, you will need a voltage converter to safely use them.
What are the advantages and disadvantages of fruit batteries?
they generate very little voltage and as such you need to use lots of fruit to produce sufficient voltage. Fruit batteries also decompose so do not last very long
Do I need a voltage converter for Scotland?
Yes, you may need a voltage converter for Scotland as the standard voltage there is 230V, which may be different from the voltage used in your country. It is recommended to check the voltage requirements of your electronic devices before traveling to Scotland.
What is conditions need to sychronaising?
The generator voltage has to be the same as the bus voltage
Engine coolant temperature sensor above or below acceptable voltage?
An engine coolant temperature sensor will usually need to be replaced when it is drawing too much or too little voltage. The sensor may also have a bad ground connection.
Why does a semiconductor have fewer electrons than a conductor?
Valence electrons only are able to cross the energy gap in semiconductors since it is greater than that of conductors. That is why semiconductors have fewer free electrons than conductors.
When do you need to convert the voltage for appliances?
You need to convert the voltage if your appliance requires less voltage than you power supply. example: appliances is 110V and power supply is 220V.
I'm using a 18.5 volts 3.5 amps charger to charge a 12 volts battery I want to reduce voltage to 15 volts and current to about or a little less than 2 amps How to reduce charging current and voltage?
You need a regulator.
How is 4160 voltage made?
Well first we need to generate voltage from electrical generator. Then if voltage are below 4160 volt step up Transformer is used and if voltage are above 4160 volt step down Transformer is used. Generally voltage produced from generator are low so we need to step up voltage to higher values such as 240 kilo volt to transmit them to longer distances to reduce power losses.
What is the need of regulation?
To regulate the voltage
