answersLogoWhite

0

"dB", aka decibels, is a logarithmic unit of measurement in base 10. A 10 dB change in signal power means that the power has changed by a factor of 10. A 20 dB change relates to a change of power of a factor of 100, etc. dB are computed using 10*log10(power). If measured in amplitude rather than power, this would convert to 20*log10(amplitude).

1.

having improper termination

using low quality cables or connectors

User Avatar

Wiki User

16y ago

What else can I help you with?

Continue Learning about Engineering

A signal increase of 1 dB represents a increase in power.?

$:&:


A signal has passed through three cascaded amplifiers each with a 4dB gainWhat is the total gain how much is the signal amplified?

A: The gains add up to 12 db


Why there is a clipping in the signal output when you change the attenuation from 20db to 0 db in function generator?

A: Clipping only occurs if the input surpasses a threshold like the Vbe of a transistor. The 20 Db is really a change3 in voltage of a 100 that is not a small change


What is a 1-dB compression point?

Devices, such as amplifiers can't be linear over all input values. At some point they just can't output the required output power. I.e. an amplifier that increases input power by a factor of 10, may not be able to amplify a signal that comes in that is, let's say 10 watts. The point where the device is outputing 1 dB less POWER (which is roughly running at 80%) than it should is the 1 dB compression point. So lets say a 10 watt signal is input, and that the signal should be amplified by a factor of 10, and should output 100 watts. Let's also say the system output power is actually 1 dB down from the expected value and outputting roughly 80 watts, 10 watts is the input 1 dB compression point. Also, look here: http://www.rfcafe.com/references/electrical/p1db.htm


What is a signal 2 times the if from the desired signal that causes interference is an?

A signal that is 2 times the frequency of the desired signal and causes interference is known as a second harmonic or harmonic interference. This occurs because harmonics are integer multiples of a fundamental frequency, leading to potential distortion or degradation of the desired signal's quality. Such interference can impact communication systems by introducing unwanted noise or reducing clarity. To mitigate this, filtering techniques may be employed to separate the desired signal from its harmonics.

Related Questions

You will have signal degradation unless you use the amplifier.?

You will have signal degradation unless you use the amplifier.


What is dB mean in signal amplifier?

dB is the abbreviation of Decibel


What is 100 kHz in DB?

Decibels (dB) is a unit used for measuring the intensity of a sound or the power of an electrical signal. Without specific context or reference levels, it is not possible to convert 100 kHz to dB as they are different units of measurement (frequency vs decibels).


How do you find SNR out in dB?

You can find the Signal-to-Noise Ratio (SNR) in decibels (dB) by taking the ratio of the signal power to the noise power, and then converting this ratio to dB using the formula: SNR(dB) = 10 * log10(Signal Power / Noise Power). This calculation helps to quantify the quality of a signal by comparing the strength of the desired signal to the background noise.


What does dB equals to?

dB (decibel) is a logarithmic measure of the ratio of two power values, for example, two signal strengths. This is often used for power gain or power loss. For example, a loss of 10 dB means that the signal degrades by a factor of 10, a loss of 20 dB means that the signal degrades by a factor of 100, and a loss of 30 dB means that the signal degrades by a factor of 1000.


What is the signal to noise ratio formula in dB?

The signal-to-noise ratio (SNR) formula in decibels (dB) is calculated as 10 times the logarithm base 10 of the ratio of the signal power to the noise power. The formula is: SNR(dB) 10 log10(signal power / noise power).


What is IP3 and IM3?

IM3 degrades the sensitivity of the desired signal as an in band spurious frequency component. IP3 determines the severity of the degradation as a measurement through the linearity of the system.


What is an example of a sound level measurement that is considered to be 55 dB?

An example of a sound level measurement that is considered to be 55 dB is a normal conversation at a close distance.


What the strongest FM signal booster?

The effectiveness or strength of FM signal boosters is roughly measured in "db". Db means decibels, a measure of signal strength above noise. A quick search revealed boosters for sale ranging from 14db to 25db. More db = stronger.


What is the unit of sound intensity measurement?

The unit of sound intensity measurement is the decibel (dB).


A signal starts at point x as it travels to point y it loses 8 db at point y the signal is boosted by 10bb as the signal travels to point z it loses 7 db what is the db strength of the signal at point?

A signal starts at point X. As it travels to point Y, it loses 10db. At point Y, the signal is boosted by 5db. As the signal travels to point Z, it loses 7db. What is the db strength of the signal at point Z?


How much loss does a typical ground block have?

A typical ground block has negligible loss, usually less than 0.1 dB. This low loss ensures that the electrical connection to ground is strong and reliable. Ground blocks are designed to minimize signal degradation in a system and maintain signal integrity.