answersLogoWhite

0

PUT A MULTIPLIER RESISTOR IN SERIES WITH THE METER AND SOURCE. RESEARCH 'METER SHUNTS AND MULTIPLIER CIRCUITS', IT TAKES ONLY ONE SMALL RESISTOR.....(OR IF YOU HAVE EXTRA METERS, PUT TWO OF THEM IN SERIES WITH THE LOAD AND SOURCE; THEN ADD THE TWO METER READINGS.)

User Avatar

Wiki User

17y ago

What else can I help you with?

Continue Learning about Engineering

Functions of the Parts of an analog multimeter?

Parts of Analog MultitesterScale Pointer position adjuster Range selector knob Meter cover Panel 0?? adjuster knob ?input terminal ?input terminal pin Plug Test lead?Red? Test lead?Black Test lead(TL-21) Arnel Gamao Jr. Parts of Analog MultitesterScale Pointer position adjuster Range selector knob Meter cover Panel 0?? adjuster knob ?input terminal ?input terminal pin Plug Test lead?Red? Test lead?Black Test lead(TL-21) Arnel Gamao Jr.


What is the main distinction between digital and analog signals?

digital systems are nothing but may be based on microcontroller, or an electronics parts which are highly sensitive, fast response and light in weight. Where as analog instruments mainly consists of mechanical parts which indicates lower accuracy compared to digital. - By. Sainath Roham


How does the meter have to connect to the battery in order to provide an indication?

The meter ( as refered to a conventional moving coil analog pointer type ) basically operates on a Direct Current ( DC ) passing in its coils. Hence the meter inherently has a polarity of operation i.e the positive & negative inputs of the meter must be connected appropriately with the corresponding positive & negative potentials in the circuit being measured , so that the meter deflection is in the correct direction of the measuring scale ( typically clockwise movement ) Bsis Voltage & current measurement scales are linear , while resistance ohmic measurement scales are generally non linear. Incorrect polarity of connection will result in the meter deflecting in the opposite direction & usually will not damage the meter unless an inappropriate measuring range was selected. Whenever the magnitude of measured voltage or current is not known approximately beforehand, the best precaution is to use the highest range on the meter & stepping down the range if the deflection is too low for a good reading.This will prevent damage to the meter due to overload deflection which generally will damgage the delicate moving parts of the meter, which results in a total writeoff. For measuring voltages , the meter configuration as a voltmeter is used, where a series voltage dropping high value resistor appropriate to the range of voltage being measured is incorporated into the meter itself. The voltmeter is always connected across the points where the measurement is required. Hence no alteration of circuit is required for this measurement. For measuirng current, a low value resistor across the coils of the meter is incorporated appropriate to the range value of currents being measured, as a shunt to divert currents larger than what the basic meter can handle. It is necessary to break the circuit at a convinient point where the measurement is required and the meter inserted into the circuit. Hence an alteration of circuit is required for this measurement. When a meter is configured to measure resistance , a low voltage battery source with appropriate circuitry is incorporated into the meter itself to read the resistance value directly in ohms. Modern digital meters generally have bipolar measurement capabilities, in which the polarity of measurement is indicated. Here only the moving coil meter is replaced by a analog to digital convertor chip which directly displays the value on the digital readout. Otherwise the same measurement principles apply.


How are analog sticks made?

Analog sticks are typically made using a combination of plastic and electronic components. The manufacturing process begins with molding the plastic parts, including the stick itself and the housing. Inside, sensors such as potentiometers or Hall effect sensors detect the movement and position of the stick, converting mechanical movement into electrical signals. Finally, these components are assembled, tested for functionality, and packaged for use in devices like game controllers.


Parts and function of Volt-Ohm-Milliammeter?

A meter that can be used to measure multiple ranges of currents and voltages is called a multimeter. A common type of multimetera combination voltmeter, ohmmeter and milliammeteris abbreviated VOM

Related Questions

What are the parts of an analog voltmeter and its functions?

An analog voltmeter measure voltage and resistance along with the current. The parts include a needle, a spring, resistors, and a way to control it. That would be a knob or rheostat.


What is the conversion factor from parts per million (ppm) to grams per cubic meter (g/m3)?

To convert from parts per million (ppm) to grams per cubic meter (g/m3), you need to know the density of the substance in question. The conversion factor will vary depending on the substance's density.


The different parts of back panel?

different parts of back punel


What is the answer if you divide a meter into 5 equal parts?

5*20 cm = 1 meter


A meter is divided into 100 equal parts called millimeters true or false?

This is a false statement because a meter is divided into 100 equal parts called centimeters and not millimeters. However, a meter can be divided into 1000 equal parts and these are called millimeters.


How do you Convert 32593.86 ppm to micrograms per cubic meter?

Ppm is parts per million. This is more commonly, milligrams per litre. To convert this to micrograms per metre cubed, you multiply by 1,000,000. 32593.86*1000000 is 32,593,860,000 micrograms per metre cubed.


Functions of the Parts of an analog multimeter?

Parts of Analog MultitesterScale Pointer position adjuster Range selector knob Meter cover Panel 0?? adjuster knob ?input terminal ?input terminal pin Plug Test lead?Red? Test lead?Black Test lead(TL-21) Arnel Gamao Jr. Parts of Analog MultitesterScale Pointer position adjuster Range selector knob Meter cover Panel 0?? adjuster knob ?input terminal ?input terminal pin Plug Test lead?Red? Test lead?Black Test lead(TL-21) Arnel Gamao Jr.


What is Convert Parts of a Million?

It is not possible to answer the question because it does not specify what to convert to.


How is the beat divided in simple meter?

In simple meter, the beat is divided into two equal parts.


What does 850 millimeters equals how many parts of a meter?

0.85 meter1 meter = 1000 millimeters 1 millimeter = 0.001 meter


What is the difference between simple meter and compound meter in music?

Simple meter in music has beats that can be divided into two equal parts, while compound meter has beats that can be divided into three equal parts. This difference affects the overall feel and rhythm of the music.


What parts start with the letter i?

Interior lights, instrument panel and ignition are car parts.