answersLogoWhite

0

Gasket

User Avatar

Wiki User

16y ago

What else can I help you with?

Continue Learning about Engineering

What is the purpose for plumbing pipe dope?

Joint compound AKA dope is used as a lubricant and to seal minor imperfections of the threads


What am I doing wrong when I can't get the solder to stick when soldering a copper pipe?

Not cleaning the pipe or joint enough, not using flux, or not heating the pipe or joint enough. You use the blue tip of the flame on the joint and the capillary action sucks the solder into the joint. You have to clean the pipe with sandpaper or steel wool, the joints with a fitting brush on the inside, and use a proper flux and solder.


What do you call 2 pipes that are joined?

Two pipes that are joined together are typically referred to as a "pipe joint" or "pipe connection." The specific type of connection can vary based on the method used, such as a welded joint, threaded connection, or flange connection. These joints allow for the flow of fluids or gases between the connected pipes while maintaining a secure and leak-proof seal.


What is the number one key to a successful copper pipe Sweat?

The number one key to a successful copper pipe sweat joint is achieving proper heat application. This involves using the right torch and flame size to evenly heat the joint without overheating the copper, which can lead to oxidation. Additionally, ensuring that the surfaces of the pipe and fitting are clean and free of oxidation or debris is crucial for a strong bond. Finally, using the appropriate solder and allowing it to flow into the joint properly will ensure a reliable seal.


Why is filet weld necessary while welding slip on flanges to a pipe end?

It is the only type of weld you can make to seal this type of joint. There are flange ends that can be welded onto pipe with a butt weld, but sockets and slip-ons must be fillet welded.

Related Questions

How do you seal cpvc pipe into brass fitting?

Pipe joint compound or Teflon tape


Why HDPE pipe is not able for rubber ring joint?

HDPE pipe can use a rubber ring, if the rubber ring is properly sealed with a steel gasket. The rubber ring must be placed in a groove in the pipe and then the steel gasket is placed on top of it.


How can I effectively seal a leaking pipe joint?

To effectively seal a leaking pipe joint, you can use plumber's tape or pipe sealant. First, turn off the water supply to the pipe. Then, clean the area around the joint to remove any dirt or debris. Apply the plumber's tape or pipe sealant to the threads of the joint and tighten it securely with a wrench. Turn the water supply back on and check for any leaks. If the leak persists, you may need to replace the joint or seek professional help.


What is pipe grooving?

Pipe grooved at end of pipe with grooving machine. Butt grooved pipe or fitting together and slip rubber seal onto end of each grooved joint, apply light coating of grease made for grooved piping on rubber seal. Coat split coupling for joint with grease also and put coupling around joint and clamp together tightly.


How can I effectively seal a copper pipe?

To effectively seal a copper pipe, you can use a soldering technique. This involves heating the joint where the pipe connects and applying solder to create a watertight seal. Make sure to clean the pipe and fittings thoroughly before soldering to ensure a secure bond.


How do you seal a bathroom sink drain pipeI recently dropped my ring down the drain and had to remove the pipe. I replaces the pipe but do not know what to seal it with?

Mission CAP or IPS plug if there is a female fitting


What is the purpose for plumbing pipe dope?

Joint compound AKA dope is used as a lubricant and to seal minor imperfections of the threads


Why is the pipe under the sink leaking at the connection?

The pipe under the sink is leaking at the connection because there may be a loose or damaged seal or fitting, causing water to escape from the joint.


What is grooves?

Pipe grooved at end of pipe with grooving machine. Butt grooved pipe or fitting together and slip rubber seal onto end of each grooved joint, apply light coating of grease made for grooved piping on rubber seal. Coat split coupling for joint with grease also and put coupling around joint and clamp together tightly.


How can use instead of Teflon Tape to seal the 4 threaded joint on galvanized air lines?

You can use pipe thread sealant aka "Pipe Dope" you can get this at most hardware stores.


Why does spout leak at the wall when shower diverter is used?

A hole has developed in the spout or where it screws onto the pipe needs more Teflon tape or joint compound to seal the threads.


What should I do if I have a PVC pipe leaking at the joint?

If you have a PVC pipe leaking at the joint, you should first turn off the water supply to prevent further leakage. Then, dry the area around the leak and apply PVC primer and cement to seal the joint. Allow it to dry completely before turning the water supply back on. If the leak persists, you may need to replace the joint or seek professional help.