0
What else can I help you with?
How do set the lifting pressure of boiler safety valve?
The lifting pressure is set by turning the adjusting nut on top of the valve.
P-trap replacement metal drain pipe from wall has swivel flange but missing slip nut. Is there a special way to still use this pipe as is with a new plastic or metal trap?
you can use a rubber connector with two "O"ring which are usually attached to the rubber. so you take rubber connection and slip it on the P tighting it and then do the same with the other side should work cost about $ 2.50
What is a retaining nut in plumbing?
A retaining nut could be the packing gland nut on a valve stem or the nut used on a flare or compression fitting
How do you put a wheel stone on a lathe?
To put a wheel stone on a lathe, first ensure the lathe is turned off and unplugged for safety. Remove the existing wheel if necessary, then align the wheel stone with the spindle and secure it using the appropriate mounting hardware, such as a nut or flange. Tighten the fasteners to ensure a snug fit, and check that the stone is properly balanced before plugging in the lathe and starting it up. Always wear appropriate safety gear, such as goggles and a dust mask, during operation.
What is the difference between screw and nut?
A nut is called screw when its head is tightend in component .but in case, tight of nut is not possible without bolt.since screw is tight without nut bolt it is not possible in case of nut.
How do you replace rear wheel bearings on a 1991 Dynasty And how tight do you torque the wheel bearing nut?
you have to press it out and press the new one in just make sure you tighting it real good
How can I remove a stripped nut from a bolt?
To remove a stripped nut from a bolt, you can try using a pair of locking pliers or a nut splitter tool to grip and break the nut. Another option is to use a drill to create a small hole in the center of the nut and then use a screw extractor to remove it. If these methods do not work, you may need to cut the nut off with a hacksaw or angle grinder. Be sure to use caution and wear appropriate safety gear when attempting to remove a stripped nut.
Why is heat used to loosen a rusted nut on a bolt?
By heating the nut (and avoiding the bolt as much as possible) the metal expands, this increases the size of the hole in the middle, releasing pressure against the bolt and allowing you to turn the nut while hot. Wear heat proof gloves, eye protection and have extinguishing equipment and cold water to hand. The level of heat required is often described as "cherry red" and can cause some types of metal to permanently change their hardness... be very careful if you are working on safety critical things like brakes, replace all affected parts.
Is it necessary to replace spindle nut on f150?
Replacing the spindle nut on a Ford F-150 is not always necessary unless it shows signs of wear, damage, or if it has been removed during maintenance. If the spindle nut is stripped or corroded, it should be replaced to ensure proper wheel assembly and safety. Always consult the vehicle's service manual for specific recommendations regarding maintenance and replacement.
What is the best way to safely replace a grinder cutting blade?
To safely replace a grinder cutting blade, follow these steps: 1. Unplug the grinder and wear protective gloves. 2. Remove the old blade by loosening the retaining nut. 3. Install the new blade, making sure it is securely in place. 4. Tighten the retaining nut and test the grinder before use.
How do I safely remove a table saw blade?
To safely remove a table saw blade, first unplug the saw. Use a wrench to loosen the arbor nut and remove it, then carefully lift the blade off the arbor. Be sure to wear gloves and handle the blade with caution to avoid injury.
How do you safely remove a table saw blade?
To safely remove a table saw blade, first unplug the saw. Use a wrench to loosen the arbor nut and remove it, then carefully lift the blade off the arbor. Be sure to wear gloves and handle the blade with caution to avoid injury.
Why does Vishnu wear so much gold?
She wore gold cause she is a hard nut
How are cashews picked?
Its is important to remove a cashew nut from its shell, due to the fact that the cashew shell is in fact toxic. To remove the shell you must be wearing gloves to protect yourself from the poison. The nut itself is removed with a knife like tool.
Where is the neutral safety switch on a 1996 Jeep?
the safety switch is on the passenger's side of the transmission. There is a rectangular shaft protruding through a 1" nut. The nut has a safety lock on it to prevent it from loosening. There are two bolts that mount the switch to the trans. The entire assembly is located just forward of the trans mount bracket, on the passenger's side of the trans.
How can I crack Brazil nuts effectively and safely?
To crack Brazil nuts effectively and safely, use a nutcracker or a hammer to apply gentle pressure to the shell until it cracks open. Be careful not to apply too much force to avoid crushing the nut inside. Wear protective gloves to prevent injury from sharp shell fragments.
What is the purpose of a stripped hex nut and how can it be prevented?
A stripped hex nut is a nut that has lost its grip on a bolt due to wear or damage, making it difficult to tighten or loosen. This can be prevented by using the correct tools and techniques when tightening or loosening the nut, avoiding over-tightening, and regularly inspecting and replacing worn nuts.
