0
If it is ball bearing, it is of higher pair. since the balls in the bearing have point contact with the surface.
if it is a journal bearing, it is of lower pair. since the jounal is having surface contact with the shaft.
This question refers to the type of pairs in a mechanical joint...
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
What is shaft bearing?
A shaft bearing is a low friction support device for a rotating member of a mechanical machine.
A support in which a shaft rotates?
Bearing.
What are the uses of footstep bearing?
A footstep bearing is essentially a cast-iron block with a gunmetal bush that has a hollow collar fitted on its top. This bearing is used to keep the shaft upright in a vertical position. The shaft is fixed in place and not allowed to rotate by a pin.
What is fixed bearing?
Due to temp. variation the shaft will expand axially, to accept this expansion only one bearing on the shaft is fixed axially in the housing, are called Fixed Bearing. It can also mean that an object is at a steady angle away from another object
Why use journal bearing in turbine?
putting a journal bearing at each end of the turbine rotor or shaft would be to support it.
How do you find diameter of a shaft when bearing no is given?
How do you find dia meter of shaft when bearing no is given?
What is shaft bearing?
A shaft bearing is a low friction support device for a rotating member of a mechanical machine.
What is the difference between a fixed and a floating bearing?
floating bearing allows axial movement of the shaft. fixed bearing does not allow for axial movement of the shaft
What is a center bearing?
That is a bearing in the centre of a crankshaft or drive shaft.
What is friction bearing?
A friction bearing is a solid bearing that directly supports the end of an axle. Friction is when the bearing and the joint are running together.
How do you remove a frozen bearing race from the shaft?
Use a die grinder with a cutoff wheel and cut the race in half taking care not to touch the shaft. If the bearing race spun on the shaft and froze on to the shaft chances are the shaft is damaged.
A support in which a shaft rotates?
Bearing.
What type of bearing is needed for power transmission in a rotary sieving machine?
Depending on the design, ball bearings or roller bearings (either flat or tapered) can be used to support the rotating shaft of a sieving machine. The design engineers will specify what needs to be stuffed into the machine to support the revolving shaft(s).
How do you remove a drive shaft carrier bearing on a 1985 ford f150?
to remove carrier bearing, u will need to removbe the drive shaft from the vehicle the carrier bearing is bolted to chassis with 2 bolts . these will need to be removed and the carrier and bearing will come out with the drive shaft one drive shaft is out you can then knock old bearing and carrier off of shaft with a hammer. the old carrier is no good so doesnt matter if you trash it once you get old one off, carefully known new one onto shaft until seated,being careful to note which is front of carrier bearing you can then reinstall cariier bearing and drive shaft to truck. NOTE: now is a good time to check and replace if needed the U-Joints on the drive shaft
Bearing on drive shaft of Camry 1998?
What about it?
How long is front drive shaft in 1963 Impala with 2 piece carrier bearing drive shaft OEM?
there is no front shaft in 63 impala Wrong answer, it's about two feet from the transmission to the carrier bearing
How do you replace carrier bearing on 1978 Chevy?
you need to unbolt the carrier bearing from the truck remove the front drive shaft by pulling it out of the yoke you will see the splines, leave the rear drive shaft in truck. cut all the rubber off the bearing i used a pair of tin snips. once you have the rubber off the bearing use a cut off wheel or grinder being careful to not hit the drive shaft to cut the bearing off the shaft they don't make a tool to pull it off. my Friend is ASEI certified and that's how he told me to do it that's how i did it on mine i cut it as close to the shaft then whacked a thick screwdriver between the baring race and it fell right off. to put it on find a long pipe to tap it on. it should go on easier than the old one came off.
