answersLogoWhite

0

1.control circuit is used for removing ripple

2.analog circuits are also used with TPS84259 negative output voltage power module to reduce the ripple

User Avatar

Wiki User

11y ago

What else can I help you with?

Continue Learning about Engineering

What is a ripple counter?

A ripple counter is a counter in which state transitions of one or more flip flops are triggered by the outputs of other flip flops in the circuit. If all flip flops in the counter are triggered by a common clock pulse, then the counter is called a "synchronous counter". a ripple counter is a counter that will ripple through the information sequentialy. .


Can I use 4026ic insted of 4033ic in same circuit?

It depends on the circuit design, and on the intended use. The 4033 is the same as the 4026, except that it has a ripple blank feature that allows leading zero blanking, while the 4026 has a similar (but subtly different) display blanking feature.


What is the minimum frequency of ripple in the output?

The minimum frequency of ripple in the output typically depends on the specific application and the design of the circuit involved. In power supplies, for example, ripple frequency is often determined by the rectification method used; for full-wave rectifiers, it is double the input frequency, while for half-wave rectifiers, it matches the input frequency. To provide a precise answer, additional context regarding the circuit type or application is necessary.


How can you measure the ripple frequency to determine if diode were open in a bridge rectifier circuit?

To measure the ripple frequency in a bridge rectifier circuit, use an oscilloscope to observe the output voltage waveform. The ripple frequency is typically twice the input AC frequency if the diodes are functioning properly since the rectifier conducts during both halves of the AC cycle. If the ripple frequency is lower than expected, it may indicate that one or more diodes are open, preventing proper rectification. Comparing the measured frequency to the expected value helps diagnose the condition of the diodes.


What is the effect of increase value of a capacitor on ripple voltage?

Increasing the value of a capacitor in a power supply circuit generally reduces the ripple voltage. This is because a larger capacitor can store more charge and better smooth out fluctuations in voltage during the charging and discharging cycles, which occurs in rectified AC signals. As a result, the output voltage becomes steadier, leading to lower ripple voltage. However, practical limitations like size, cost, and equivalent series resistance (ESR) must also be considered.

Related Questions

What figurative language is ripple?

Ripple refers to an AC component riding on an DC rail but it can refers to others circuit as well.


How do you convert a ripple counter to a decade counter?

Add a circuit to reset it when it hits 10. Yes it will glitch, but ripple counters already glitch.


Why ripple carry adder is used?

A ripple carry adder needs a much less complicated circuit, than other adder topologies.


What is a ripple in cheerleading?

A ripple in cheerleading is when the cheerleaders do the same moves on different counts. like a wave.


What will happen if the capacitor is removed from the DC charger?

It will increase the ripple factor that the capacitor is in the circuit to smooth out.


What is diode ripple?

In a switching DC-DC voltage converter, the oscillatory nature of the switching circuit generates a small "ripple" effect in the output voltage which is supposed to be minimized via careful design of the overall circuit. The output current of this type of converter typically flows through a diode into the rest of the system. The voltage measured at the cathode of this diode will exhibit the aforementioned ripple.


What is a ripple counter?

A ripple counter is a counter in which state transitions of one or more flip flops are triggered by the outputs of other flip flops in the circuit. If all flip flops in the counter are triggered by a common clock pulse, then the counter is called a "synchronous counter". a ripple counter is a counter that will ripple through the information sequentialy. .


Significance of the ripple voltage on a rectifier circuit?

A: It really depends on the load requirement . Example driving a relay hi ripple with no capacitor is an advantage in efficiency for a sensitive amplifier it will cause mayhem with the performance


Can I use 4026ic insted of 4033ic in same circuit?

It depends on the circuit design, and on the intended use. The 4033 is the same as the 4026, except that it has a ripple blank feature that allows leading zero blanking, while the 4026 has a similar (but subtly different) display blanking feature.


What is a ripple?

Ripple is the oscillations that can arise in a circuit when a signal changes suddenly. It stems (in analog circuits at least) from stray capacitances and inductances forming a resonator.Answer--Ripple can refer to: * Ripple (charitable organisation)* Ripple effect, the socio-educational phenomenon* Ripple (electrical), residual unwanted variations following ac to dc conversiono Frequency domain ripple, the ripple of a filter's insertion loss* Ripple (fluid dynamics) for capillary waves* Ripple, Kent, a village in Kent, England* Ripple, Worcestershire, a village in Worcestershire, England* Ripple marks, as identified in sediments and sedimentary rocks* Ripple monetary system* Ripple (wine)it is also a cheerleading move! it is when you take a step clap turn take a step yurn and you bend your knees do a high v put your arms together to the side bring it to you and swing your arm then jump *smile*


What is a different word for wave?

"Ripple" is a good word.


What is the minimum frequency of ripple in the output?

The minimum frequency of ripple in the output typically depends on the specific application and the design of the circuit involved. In power supplies, for example, ripple frequency is often determined by the rectification method used; for full-wave rectifiers, it is double the input frequency, while for half-wave rectifiers, it matches the input frequency. To provide a precise answer, additional context regarding the circuit type or application is necessary.