answersLogoWhite

0

Foundations are the main cause of any building sinking. As the house moves its structure is under differing stresses and this causes the fabric of the housee o eventually break in areas such was walls, floor/ceilings and door ways and windows start becoming twisted.

User Avatar

Wiki User

∙ 12y ago
User Avatar

What else can I help you with?

Continue Learning about Engineering

Sag produced in the conductor of a transmission line depends on?

-The tension of the cable (the tighter, the less sag, but this can cause other problems if too tight) -The temperature outside (the higher the temperature, the more it will sag) -The amount of current flowing through the cable (the more current, the hotter the conductor will get = more sag) -The type of cable (aluminimum will sag more than copper; ACSR will sag less than straight aluminimum).


When Ontario Hydro workers set up electrical cables during the summer they allow the cables to sag. Suggest a reason for this. In your answer refer to the particle theory?

i know someones going to be on this sooooooooo....... they sag because the hydro workers know, from the heat the cbles will sag during the summer, so they start the sag so they cant sag anymore


How do sag's in power transmission formed?

The plural of sag is sags, not sag's! Sag is caused by the weight of the conductor between its supports, and is (a) unavoidable and (b) necessary to allow for the conductor's expansion and contraction during variations in temperature. When surveyors design a power line, the amount of necessary sag is calculated and built into the design, while ensuring that the clearance between the conductor and the ground remains within safe limits.


How do you calculate the sag of a cushion under weight?

To calculate the sag of a cushion under weight, you first need to determine the cushion's material properties, such as its stiffness or spring constant (k). Then, apply Hooke's Law, which states that the force (F) exerted on a spring is equal to the spring constant multiplied by the displacement (sag) (F = k * s). By rearranging the formula, you can find the sag by dividing the force applied (the weight of the object) by the spring constant (s = F/k). Measure the weight in newtons and ensure the spring constant is in compatible units to get the sag in meters or inches.


What is Sag Compensating Springs for Pantograph Isolator?

i think sag compensation springs are used in dead end termination of quadra conductor bus where jack bus is passing below bus & required clearence if we are not getting betn two buses their these sag compensation springs are used to bring conductor under tension .

Trending Questions
What are the application areas of electronic sheet? What is the Core SRP program that provides centralized management planning prioritization and programming? Why is it important to place a potentiometer in the wheatstone bridge ohmmeter circuit? Resource typing involves the categorizing of resources based on? Engineered Flooring vs. Solid Hardwood Flooring? What is the position of 6g pipe welding? In a certain balanced three-phase system each line current is 5 a and each line voltage is 220 v what is the approximate real power if the power factor is 0.7? Where could I research different types of sprinkler systems? What is Normalization Explain the condition under which a relation needs to be normalized to 3 NF fro3 2 NF with the help of an example? How much energy does a 12 V battery in your car use to move 2.5 C through the electical circuit? Which is better the 6600 mah or 4000 mah for the battery of a tablet? What is pstn network how it works is it reliable source of communication? What is the formula for shafts alignment? Can a cement mixer be used for mixing concrete and vice versa? What are similarities and dissimilarities between a motor and an electric generator? My howrse account won't work on version 2 it says javascript not activated but I checked and it is what should I do? How do you select Pneumatic cylinder? What is the difference between a c ration and a k ration? Should science comes first to technology? Should you wear ESD wrist strap when working on power supply DC output?