0
What else can I help you with?
How do you make bus port connectors in Logic Works?
Press Ctrl+B (or alternative go to "Schematic" --> " New Breakout") Enter the Bus name followed by the number of pins you want and press OK. example for name is D0..2 -> creates Bus D with signals D0, D1 , D2
What is assembler operation in bus encoding?
Assembler operation in bus encoding refers to the process of translating assembly language instructions into machine code that the hardware can execute. This involves encoding the data and operation codes (opcodes) into binary format suitable for transmission over a bus system. The bus encoding ensures that the signals representing the instructions and data are efficiently transmitted between various components of a computer system, minimizing errors and maximizing speed. Overall, it plays a critical role in the interface between software and hardware.
How many bytes of date can be addressed by a computer system with an 11-bit address bus and an 8-bit data bus?
There can be one byte of data transferred at one time on the 8-bit data bus, but without knowing more about the architecture and the address and data bus multiplexing we cannot know how many bytes can be addressed.Perhaps the machine architecture uses 2 address bus cycles to send out a 16-bit address and 6-bits of control signals, then uses 2 data bus cycles to read or write the 16-bit word at that address, which would mean this computer system addressed two bytes at one time.Perhaps the machine architecture uses 3 address bus cycles to send out a 32-bit address and a 1-bit control signal, then uses 4 data bus cycles to read or write the 32-bit word at that address, which would mean this computer system addressed four bytes at one time.Perhaps the machine architecture uses 6 address bus cycles to send out a 64-bit address and 2-bits of control signals, then uses 8 data bus cycles to read or write the 64-bit word at that address, which would mean this computer system addressed eight bytes at one time.Perhaps the machine architecture has a variable word length (which could be specified in many different ways depending on the architecture), in which case almost any number of bytes could be addressed at one time (with different numbers of bytes in each addressing operation).There are many other possibilities.
Name three types of buses that are likely to be on a motherboard today?
data bus, system bus and host bus.
When was IC Bus created?
IC Bus was created in 2002.
What is bus in 8085?
there are mainly 3 buses are there in 8085. They are: Address bus :-Used to carry address Data bus :- Used to carry data Control bus :-Used to carry signals such as control and timing signals
What bus Inside the processor housing data instructions addresses and control signals?
front side bus
Inside the processor housing data instructions addresses and control signals travel on the bus?
Internal Bus
What are the four categories of cargo carried over a bus?
Electrical power, Control Signals, Data, and Memory Addresses. (CPU BUS)
What is the function of control bus in references to 8085 microprocessor?
It provides timing signals.
What is Buses and what does it do?
Data bus - transfers data round system address bus - CPU provides the addresses to where the data must be fetched, through this bus control bus - timing and signals which control data flow in the system.
What does a video bus do?
A bus in a computer is an electronic path between points in a system. A video buss is a path between devices that transmit video signals.
What is bus unit?
The bus interface unit is the part of the processor that interfaces with the rest of the PC. Its name comes from the fact that it deals with moving information over the processor data bus, the primary conduit for the transfer of information to and from the CPU. The bus interface unit is responsible for responding to all signals that go to the processor, and generating all signals that go from the processor to other parts of the system.
What are the 3 categories of Front Side Bus signals?
1. Data Signal Group 2. Address Signal Group 3. Common Clock Signals
Which three system resources are commonly used for communitacion between the CPU or memory and other components in the computer?
System Bus, Address Bus & Control Signals.
What is the function of the terminator in a bus topology?
To prevent signals from being echoed back through the network
What is purpose of terminator on bus topology?
In a bus topology, the purpose of a terminator is to absorb signals at both ends of the bus cable, preventing them from bouncing back and causing network interference. Without terminators, signals could reflect back along the bus, leading to data collisions and communication errors. By ensuring proper signal termination, terminators help maintain the integrity of data transmission across the network.
