answersLogoWhite

0

What else can I help you with?

Related Questions

How do you change the egr valve on a 96' dodge neon?

The EGR valve and electrical transducer should be replaced at the same time as they are matched. Remove EGR transducer from the air inlet duct. Disconnect vacuum supply tube from EGR transducer solenoid. Remove air inlet duct. Remove EGR tube to EGR valve screws. Remove EGR valve mounting screws. Remove EGR valve and transducer. Clean gasket surfaces. Discard old gaskets. If necessary, clean EGR passages. Loosely install EGR valve with new gaskets and finer tighten EGR tube fasteners. Tighten tube fasteners to 95 in lb, tighten EGR valve mounting screws to 200 in lb. Install air inlet duct. Connect vacuum supply tube to solenoid. Attach electrical connector to solenoid. Install EGR transducer onto air inlet duct.


After replaced transducer of EGR but the check light still on what should you will replace next?

try the solenoid controlling the egr


Where can you find the EGR valve on a 1996 L4 2.4 Dodge Stratus?

The Haynes Automotive Repair Manual (for Chrysler Cirrus Dodge Stratus Plymouth Breeze)1995 - 2000 shows the EGR Valve on the BACK of the engine block (passenger side) with the Solenoid/Transducer mounted just above it. (Figure 6.1a - Page 6-13). Tubing runs from the Exhaust system to the EGR Valve and from the EGR Valve to the Solenoid/Transducer and from the Solenoid/Transducer to the Intake Manifold. Try following the tubing. ...


How do you test a back pressure transducer?

make sure you have vaccum to the transducer, i believe there will be 2 hoses coming from the throttle body. make sure that the metal line that connects to the bottom of the transducer is not clogged with carbon. if you have vaccum and that line is clear, take the hose that goes to the egr vsv solenoid off the transducer and rev the engine up. if it is good you will have vaccum through the transducer, if its bad no vaccum will be there. <(")


Where do you find the egr on a 96 mercury villager?

The EGR valve is located on the top of the intake manifold rearward of the throttle crank under the cowl. If you suspect a problem with the system, you may want to check the EGR control solenoid, the EGR control backpressure transducer and all vacuum hoses.


Where is egr control solenoid filter located on 95 Dakota?

It's inside the transducer. The black solenoid that's attached to the egr valve by two vac lines. 3.9L and 5.2L have a power plug and 2.5L isn't powered.


List of active transducer?

thermocouple,piezoelectric transducer,photoelectric transducer.


Who invented transducer?

transducer was invented by


Where is the egr valve 1996 dodge neon There is nothing attached to your air inlet 2.0 sohc?

EGR Valves for 95-99 dodge neons are bolted to the transmission side of the cylinder head; below and to the right of the cam position sensor. It has 2 rubber vacuum hoses and a steel tube that connects it to the intake manifold below the throttle body. Do not confuse the EGR valve with the Electronic EGR Transducer which can be identified by the electrical connector, the EGR valve does not have any electrical connectors attached to it.


What is prncipal of transducer?

The basic principle of a transducer: A transducer which converts a physical quantity to the electrical quantity.


What type of transducer Is potentiometer?

what type of transducer potentiometer


What is pressure transducer?

please give a simple defineatoin of transducer.