0
What else can I help you with?
How do you decrease water pressure in a urinal that has no visible valve to do so?
flow restrictor
What is the flow rate of a showerhead?
It depends on what shower head you have. It is not an exact answer. ANS 2 - The average shower head has a restrictor limiting it to about 2gpm. These can be removed and then you would get about 3 gpm.
The hot water pressure in the shower is still low after replacing the valve stem and seat?
Open up the actual shower head and remove the factory fitted restrictor.
How do you remove flow restrictor in a moen shower head?
very carefully actually call moen, they are very very helpful, i scratch the plate of my mixture assembly and they sent me i knew one free of charge, infact they also sent me another part just incase.
Should the cold-water inlet and hot-water outlet be the same size on a 50-gallon electric water heater?
The inlet and outlets are the same size on a tank, weather your plumbing is the same size should be the question. This is not critical, but they should be the same,if there is no backflow restrictor on a plubic line and the inlet is larger then the outlet,then you could be pushing hot water into the pubic line. New installs recommend an expansion tank,but few people install them,unless they get water hammer,knocking sounds. But most new water heaters have a restrictor built into the inlet. There is no difference between gas and electric, the water does not know how it is being heated.
What is a current flow restrictor?
A current flow restrictor is a diode.
What is a restrictor plate in NASCAR racing?
A restrictor plate is a device used to reduce air flow and horsepower in a nascar engine. The restrictor plates are used at Talledega and Daytona to reduce speeds for safety.
Where is the exhaust restrictor located on a Yamaha PW80?
The exhaust restrictor is located inside the exhaust pipe where it comes out of the head.
How can I remove the water restrictor from a handheld shower head?
To remove the water restrictor from a handheld shower head, you can typically unscrew the shower head from the hose and locate the restrictor inside the shower head. Use a pair of needle-nose pliers or a screwdriver to carefully remove the restrictor. Be cautious not to damage the shower head in the process. Once the restrictor is removed, reassemble the shower head and test the water flow to ensure it has increased.
How do you remove flow restrictor in a danze shower head?
Remove the shower head, careful not to damage the finish - use a cloth and an adjustable wrench. With the head removed, use a Phillips head screw driver and unscrew the plastic restrictor. After the restrictor is a screen which might need to be cleaned. I had to remove the restrictor from mine because it caused the shower to squeal.
Is there a restrictor plate on a 1994 GM 5.7L 350 C.I. wit TBI and if there is will you get more power if you remove it?
no restrictor plate- ASE and GM MASTER TECHNICIAN
How do you take the govenor off a 50cc Chinese moped 50cc NST or Maui Dreamer?
de restrictor for a hustian 50cc de restrictor for a hustian 50cc
How can I clean or replace a flow restrictor in my washing machine to improve its performance?
To clean or replace a flow restrictor in your washing machine, first locate the restrictor near the water inlet valve. Remove it carefully and clean any debris or buildup. If cleaning doesn't improve performance, replace the restrictor with a new one. This can help ensure proper water flow and enhance the washing machine's efficiency.
How do you increase speed on 50cc scooter 4 stroke engine?
Take out the top speed restrictor plate. If you don't know how to do it contact a proffesional. where are the restrictor plates located
How do you take out a restrictor on a Yamaha Virago 535?
having just bought my 535 and wanting to take off the restrictor,i rang around various restrictor kit companies and some local yam garages and they say for my model a'91 2yl there is only a exhaust kit. there is not a kit for the carb!
How does one remove the restrictor on a 1994 Yamaha xt 350?
There should not be a restrictor on a 1994 year model, I'm sure the only ones that have it are the ones between 1990 & 1993.
How do you prevent back flow of water from a tank?
You can prevent back flow of water from your tank by installing a back flow restrictor valve. The restrictor valve will allow fluid to flow in one direction.
