0
What else can I help you with?
How do you find bandwidth by fdm?
To find bandwidth using Frequency Division Multiplexing (FDM), you first determine the frequency range allocated for each channel within the system. Bandwidth is calculated by subtracting the lowest frequency of the first channel from the highest frequency of the last channel in the multiplexed signal. Additionally, you should account for guard bands, which are unused frequency gaps between channels to prevent interference. The total bandwidth is the sum of the individual channel bandwidths plus any guard bands used.
Why low frequencies are not used for data transmission in computer networks?
Low frequencies are avoided for data transmission in computer networks to prevent data loss due to attenuation of the signal. Also, low frequencies are incapable of transferring data at the speeds of higher frequencies.
Difference between drainage channel and irrigation channel?
A drainage channel is designed to remove excess water from an area, such as rainwater or wastewater. It is typically sloped to allow water to flow away from the area and may have a grate or cover to prevent debris from entering. An irrigation channel, on the other hand, is designed to bring water to an area for the purpose of watering plants or crops. It may be lined with concrete or other materials to prevent erosion and may have gates or valves to control the flow of water.
What is a cavity combiner in a communication system?
A Cavity Combiner is a device which allows the outputs of two or more transmitters on different frequencies to be combined. It uses bandpass filters on each input to prevent the signals from the other transmitters from entering the output of a transmitter.
What is lap 12mm steel bars?
Lap 12mm steel bars refer to the practice of overlapping or joining two steel reinforcement bars (rebar) that are each 12 millimeters in diameter. This technique is commonly used in construction to ensure structural integrity and continuity in reinforced concrete structures, especially when the length of a single bar is insufficient. The overlapping section, or lap length, is critical for ensuring effective load transfer between the bars. Proper lapping techniques help prevent issues such as cracking or structural failure in concrete elements.
What is purpose of guard band?
Also called a frequency guard band, a narrow frequency band between adjacent channels in multiplexing that is kept unused to prevent the channels from overlapping and causing crosstalk among modulated signals. Guard bands are commonly used in FDM but are also used in any data transmission method that relies on frequencies.
How much minimum bandwidth is required for multiplexed channel?
The minimum bandwidth required for a multiplexed channel depends on the number of channels being multiplexed and the bandwidth of each individual channel. In general, the total minimum bandwidth needed is the sum of the bandwidths of all the channels being combined. For example, if you are multiplexing four channels, each requiring 1 MHz, a minimum bandwidth of 4 MHz would be necessary. Additionally, some multiplexing techniques may require guard bands to prevent interference, which would increase the total bandwidth requirement.
Do Stable allele frequencies prevent microevolution?
No, stable allele frequencies do not prevent microevolution. Microevolution involves changes in allele frequencies within a population over time, even if those frequencies are stable for a period. Evolution can still occur through mechanisms such as genetic drift, selection, and gene flow, even if allele frequencies are temporarily stable.
Why low frequencies are not used for data transmission in computer networks?
Low frequencies are avoided for data transmission in computer networks to prevent data loss due to attenuation of the signal. Also, low frequencies are incapable of transferring data at the speeds of higher frequencies.
Does GPS satellite have the same frequency with AIS?
GPS Satellites use two frequencies 1.57542 GHz and 1.2276 GHz. AIS operates in the Marine VHF band using channels 87B, 161.975 MHz and channel 88B, 162.025 MHz
Who can we prevent roofs from water?
The sloping roof of a house is covered in an overlapping covering of slates or tiles, forming a waterproof weather protection.
Why is guard band necessary in FDM?
Guard bands are necessary in Frequency Division Multiplexing (FDM) to prevent interference between adjacent channels. They act as buffer zones that reduce the risk of crosstalk, which can occur due to overlapping frequency ranges or imprecise filtering. By providing these additional unused frequency bands, guard bands help maintain signal integrity and improve overall system performance. Without them, the quality of the transmitted signals could degrade significantly.
How do insert a transition without it overlapping the next 'slide' in Microsoft Movie Maker?
You can't do that in any video editing software that I know of. The whole concept of a 'transition' is 'movement from one frame to another'. Therefore, you can't prevent a transition from overlapping the next frame.
What are the effects on the human ear when exposed to hearing different frequencies?
Exposure to different frequencies can affect the human ear in various ways. High frequencies can cause hearing loss and damage to the delicate structures in the inner ear, while low frequencies can cause discomfort and distortion in hearing. It is important to protect your ears from prolonged exposure to loud sounds at any frequency to prevent long-term damage.
How should one properly tape their feet to prevent blisters?
To prevent blisters, properly tape your feet by using adhesive tape or moleskin to cover areas prone to friction. Make sure the tape is smooth and snug, but not too tight. Avoid overlapping tape to prevent rubbing.
Do parental controls keep you from seeing your channel stats on socialbladecom?
The parental controls goes not in any way prevent you from seeing the channel stats on socialbladecom. The parental controls only help the parents prevent their children from watching certain channels.
How can I install J channel properly?
To install J channel properly, first measure and cut the channel to fit the area. Then, nail or screw the channel into place, making sure it is level and secure. Finally, seal the joints and edges with caulk to prevent water infiltration.
