0
What else can I help you with?
What is a programmable timer?
A programmable timer usually just means a timer that can be programmed to go off at any time.
Why timer can be used in star delta starter?
delay timer
How working of the microcontroller baesd industril timer?
There are different types of industrial timer like ON Timer, OFF timer, Cyclic Timer, sequential timer there basic function is the same to turn ON/OFF devices at particular time or after a specific durations check this link for a simple microcontroller based ON timer where where a device is turned ON for a specific duration after a switch is pressed http://www.dnatechindia.com/index.php/Code-Library/8051_ASSEMBLY/ON-Timer-Program.html here is another link for adjustable cyclic timer where a device is turned ON/OFF continuously for a specific duration http://www.dnatechindia.com/index.php/Kits/Microcontroller-Kits/Adjustable-Cyclic-Timer.html
Timer in Flash - How to stop it?
Hello,I am learning how to make a timer to my game. It is something like "Who wants to be a millionaire?" I have 15 questions. There is timer for each question:60 seconds.... When I click on an answer I go on next frame, but my timer does not stop. What should I add ( and where ) to stop my timer when I clik an answer? My code for the timer is:timer = 60;countdown = function(){_root.timer--;if(_root.timer
How do you set a noma light timer?
To set a Noma light timer, first plug the timer into an outlet and then plug your lights into the timer. Turn the timer dial to the current time and set the "on" and "off" times by turning the pins or sliders to the desired time slots. Make sure to push any necessary buttons to activate the settings, and finally, ensure the timer is in the "auto" mode for it to operate according to your schedule. Always refer to the specific model's manual for detailed instructions.
What solutions prevents a router from accepting or sending out routing information for a certain amount of time?
-Holddown timer
What is the default value of the RIP hold-down timer?
180 seconds
Why is the show ip route command important for troubleshooting commands?
Compared to RIP, EIGRP has a lower administrative distance. Compared to EIGRP, RIP has a higher metric value for the route. Compared to RIP, the EIGRP route has fewer hops. Compared to RIP, EIGRP has a faster update timer.
What are features of RIP?
RIP Characteristics " RIP has the following key characteristics: RIP is a distance vector routing protocol. RIP uses hop count as its only metric for path selection. Advertised routes with hop counts greater than 15 are unreachable. Messages are broadcast every 30 seconds. The data portion of a RIP message is encapsulated into a UDP segment, with both source and destination port numbers set to 520. The IP header and data link headers add broadcast destination addresses before the message is sent out to all RIP configured interfaces.
What are the four timers used in TCP?
Connection establishment timer, persist timer, keepalive timer, retransmission timer
Is timer a short vowel?
The i in timer is a long vowel and the e in timer has a short vowel.
Is there a timer on the blackberry curve?
it depends on if you mean a camera timer or an overall timer.. if an overall timer then yes. if a camera timer then no, none of the blackberry's have a timer for your camera. but if you go on app world and type in "nux shoot" you will get one, it is completely free and great.
What would happened if you wired a 240v ballast and a 120 v ballast into a heavy duty timer?
The timer has to be multi-pole. The ballast must be connected to the load contacts of the timer. If the timer is a 120 Volt timer, the timer has to run on a 120V. circuit. Loads are loads, and as long as you have a multi-load timer you can hook up whatever you want. If the timer only works on a shared power source (load shares the timer supply) you will need to use a contactor on the load side or the timer.
How can I test a dryer timer to ensure it is functioning properly?
To test a dryer timer, you can use a multimeter to check for continuity in the timer contacts. Set the multimeter to the ohms setting and touch the probes to the timer contacts. If there is continuity, the timer is functioning properly. If not, the timer may need to be replaced.
How do you implement a WD timer in software?
wd timer
How many digit in a timer?
There are eight bits in a timer.
Is Timer short vowel?
The i in timer is a long vowel and the e in timer has a short vowel.
