0
That depends on how your sewage is treated, it could go into a septic tank in your garden or it could go into the public sewer and on to a sewage treatment works (sewage farm). In both cases raw sewage is prevented from discharge directly into the environment and the sewage is retained until natural processes have converted it into water that is safe to discharge.
What else can I help you with?
Plumber problems the drain makes gurgling sounds when you flush the toilet and the water goes down in the toilet when the other toilet gets flushed?
either the vert is plugged and there is no air getting through or there is no vent at all
What was the purpose of the toilet?
the purpose of the toilet is to go #2 & #3 and for the waste that comes out to go down the drain and get clean and it does it over and over again
What if you flush a pair of underwear down the toilet?
It will more than likely plug the toilet and/or drain line and cause a flood and backup of the sewer
What is flushed down the toilet?
Water and waste
How do toilet plungers work?
While water will compress, it does so very little and so in a confined area, like a drain pipe, acts very much like a solid. When there is a blockage in a line with water backed up behind it, such as a sink drain or toilet, the rubber cup of the plunger acts to make a seal so that when you push on the handle, the water caught between the plunger seal and the blockage is pushed down the drain as if it were solid, thus forcing the blockage down the drain. This often moves the blockage to a larger portion of the drainage system, past the place where it is caught or simply breaks up the blockage so that it can flow down the drainage system.
Why does water run in the toilet bowl?
Water runs in the toilet bowl to maintain proper water levels and to flush waste down the drain when the toilet is flushed.
How to drain a toilet properly?
To drain a toilet properly, turn off the water supply valve located behind the toilet. Flush the toilet to remove most of the water. Use a plunger to push any remaining water down the drain. You can also use a wet/dry vacuum to remove water if needed.
What is the purpose of the water pipe in a toilet system?
The purpose of the water pipe in a toilet system is to supply water to the toilet tank, which is necessary for flushing waste down the drain.
Why is the toilet bowl empty of water?
The toilet bowl is empty of water because the water has been flushed down the drain, carrying waste with it.
Why does water drain from the toilet bowl after flushing?
Water drains from the toilet bowl after flushing because the force of the flush pushes the water down the drain pipe, creating a suction effect that pulls the water out of the bowl.
Why does the toilet flushes but the water doesn't go down?
The toilet may flush but the water doesn't go down if there is a clog in the drain pipe or if the water level in the tank is too low to create enough force to push the water down.
When you flush your toilet the water rises in the bowl and the stuff doesn't flush away What is wrong?
The main drain is plugged. You may need to remove the toilet and snake directly down the drain.
How to drain a toilet for removal?
To drain a toilet for removal, start by turning off the water supply valve located behind the toilet. Flush the toilet to remove most of the water from the tank and bowl. Use a plunger to push any remaining water down the drain. You can also use a wet/dry vacuum to suction out any remaining water. Once the toilet is drained, you can disconnect the water supply line and remove the bolts securing the toilet to the floor. Lift the toilet straight up and out of the way for removal.
Do you glue the toilet flange into the toilet drain?
Usually toilet flange is glued down onto plastic drain pipe. There is a toilet flange that can be glued inside of plastic drain pipe also.
How do you drain a toilet bowl effectively?
To drain a toilet bowl effectively, start by turning off the water supply valve located behind the toilet. Next, flush the toilet to remove most of the water. Use a plunger to push any remaining water down the drain. You can also use a wet/dry vacuum to suction out the water. Finally, use a sponge or towel to soak up any remaining water in the bowl.
Why is the toilet bowl empty?
The toilet bowl is empty because the water has been flushed down the drain, leaving the bowl dry until it is refilled with water for the next use.
How can I effectively drain water from the toilet bowl for cleaning?
To effectively drain water from the toilet bowl for cleaning, start by turning off the water supply valve located behind the toilet. Next, flush the toilet to remove most of the water. Use a plunger to push any remaining water down the drain. You can also use a wet/dry vacuum to suction out the water. Remember to wear gloves and use a towel to soak up any excess water.
