answersLogoWhite

0

Tool is just a method or you can say software or hardware which is helpful for doing some inventions or new things or to test something which we want to make but first we want to test that will work hopefully or not.

User Avatar

Jessie Zieme

Lvl 10
2y ago

What else can I help you with?

Continue Learning about Engineering

What are some synonyms for the term 'tooling'?

The term tooling means to decorate. Some synonyms for "tooling" include design, braid, color, trimming, trinket, wreath, sequin, doodad, and fandangle.


What are the various turning operations that can be performed and the shapes and types of tooling that can be used (such as solid speed tooling?

Turning operations include external turning (creating cylindrical shapes), internal turning (boring holes), facing (flat surfaces at the end of a workpiece), and taper turning (producing conical shapes). Tooling types commonly employed in these operations include solid carbide tools, high-speed steel (HSS) tools, and insertable tooling systems, which can accommodate various insert shapes like round, square, or triangular for specific applications. The choice of tooling material and geometry depends on factors like the workpiece material, desired finish, and cutting conditions. Additionally, tools may be coated to enhance wear resistance and reduce friction.


What is the cutting speed for Polypropylene while machining the piece?

The cutting speed for machining polypropylene typically ranges from 150 to 300 meters per minute (m/min), depending on the specific machining operation and tooling used. Factors such as the type of cutter, machine conditions, and desired surface finish can influence the optimal cutting speed. It's advisable to start at a conservative speed and adjust based on the material's response and the quality of the machining process. Always consult the tooling manufacturer's recommendations for precise settings.


Why tooling hole in aircraft structural parts is required?

An aircraft is built by attaching many parts together. The construction of each part takes place individually, usually in lathes, milling machines, presses, etc. For the part to be accurately located inside these machines -while it is taking shape and basically being produced- it needs holes to hold it in place. While these holes can sometimes have an active function when the part is being installed or operated, this is usually not the case. A structural engineer should analyze every part so that the tooling holes -and its overall shape and characteristics- do not present a problem.


What problems could occur with setting up the work holding devices and tooling and how would you overcome them?

Problems with setting up work holding devices and tooling can include misalignment, inadequate clamping force, and tool wear. To overcome these issues, it's essential to ensure precise measurements and alignments during setup, use appropriate clamping techniques to secure the workpiece firmly, and regularly inspect and maintain tools for optimal performance. Additionally, implementing a checklist for setup procedures can help ensure consistency and reduce errors. Training operators on best practices further minimizes potential issues.

Related Questions

When was Tooling University created?

Tooling University was created in 1999.


What is ATS Automation Tooling Systems's population?

The population of ATS Automation Tooling Systems is 3,500.


What is the difference between B-tooling and D-tooling tablet compression machine?

Difference between B and D toolingD toolingBarel Diameter is 1 inchHead Diameter is 1 and ¼ th inch length is 5.25 inchDies outer diameter is 0.945 andBB TollingBarel Diameter is 0.75 inchHead Diameter is 1 inch length is 5.25 inchDies outer diameter is 30.16 mmB tooling is same as BB only difference is that lower punch length is just 3 and 9/16th inch long.D tooling dies and punches are usually have thick diameter or have greater diameter of their body as well as the tip of punches also dies have greater outer diameter compared to B type tolling which makes D type tolling dies and punches suitable for compression of big size tablets as the tip of the pinches is border compared to B tooling dues and punches.Many sub categories like DB , BB type tablets dies and punches are made depending up on the punches and dies requirement of product.Following table will be useful in understanding the concept of tablet tooling and how they are classified as B and D tooling and BB and DB tooling


What is the difference between b tooling and d tooling?

B tooling is having head and body more than d tooling As b has 1.5 & length of 5.13 body 1 inch d has 1 inch head and length 5.13 body 0.73


What are some synonyms for the term 'tooling'?

The term tooling means to decorate. Some synonyms for "tooling" include design, braid, color, trimming, trinket, wreath, sequin, doodad, and fandangle.


What is involved in 'injection mold tooling'?

Injection mold tooling is done by fusing powder to create mold geometry, then filling with bronze. You can learn more about Injection Mold Tooling at the Dinsmoreinc website.


What is the value of a 12 gauge browning bar over and under tooling master?

A Bar is not an over under, and what do you mean by tooling master?


How many Super Bowl rings does Mike Tooling have with the Pittsburgh Steelers?

Mike Tooling is not listed on the Steelers all-time roster.


How much space may tooling occupy in a class 1000 clean room?

HI, Depends up on the size of room and size of tooling can keep how many you need. .Only thing to be taken care is that the tooling & machine is environmentally friendly and ensures a safe and clean room work environment. We use clean room class 1000, keeping many presses and tooling. Rasheed.


What is progression tooling?

Love tool.


Where is the Greater Meadville Tooling Center in Erie Pennsylvania located?

The address of the Greater Meadville Tooling Center is: Po Box 3748, Erie, PA 16508-0748


HR?

Progressive tooling systems offer several benefits: