answersLogoWhite

0

A grade beam is a horizontal structural element that spans between supports right at ground level. Usually it's a reinforced concrete wall anywhere from 12" to 30" high with only about 8" above ground. The supports it sits on are concrete piers that are buried below the frost line around 4 ft. underground and sit on a footing. In the case of a stair, it's probably spanning across the front at the lowest tread and is half buried in the ground. It allows for a solid concrete exterior stair to be supported on top of it across its whole width on the corners. Eliminating the need for pouring a full height foundation wall. This application is ideal for hard rocky sub-ground where excavating would be extremely expensive. - Residential Architect, ID

User Avatar

Wiki User

17y ago

What else can I help you with?

Continue Learning about Engineering

When two or more individual column footing are jointed by a beam it is called?

Combined footing


What do you call the beam that lies along a wall and carries the load of a staircase?

The beam that lies along a wall and carries the load of a staircase is called a "stringer." Stringers support the treads and risers of the stairs, providing structural integrity and stability. They are typically positioned on either side of the staircase or in the center, depending on the design and configuration of the stairs.


What is definition of isolated footing and how it design?

Isolated footing Transfers individual column loads directly to the soil. If a single spread footing interferes with another spread footing, the two can be combined to form a combined footing.


Should there be a bed under a plinth beam?

Firstly, it is more appropriate to call this type of beam a "grade beam". It is not mandatory to provide a bed (of PCC or brickwork) beneath a grade beam in framed structures. However, it is advisable to provide one under the following conditions or when considering the following circumstances: 1. Unevenness of the ground on which the beam is laid. 2. Reducing cover to reinforcement for structures in contact with soil. 3. To prevent erosion of disturbed earth from below the beam. 4. Mobilization of elastic support throughout the length of the beam in the event of an over-load such as support settlement or earthquakes.


Is it harder to build a spiral staircase or a straight staircase?

It is harder to build a spiral Staircase because if you build a spiral staircase it will be longer and twistier than a straight staircase.

Related Questions

When two or more individual column footing are jointed by a beam it is called?

Combined footing


How do you calculate of steel in beam and footing?

get dearer


What is footing tie beam?

footing tie beams is to avoid differential settlements (HIBA MORTADA)


What is tie beam?

footing tie beams is to avoid differential settlements (HIBA MORTADA)


What do you call the beam that lies along a wall and carries the load of a staircase?

The beam that lies along a wall and carries the load of a staircase is called a "stringer." Stringers support the treads and risers of the stairs, providing structural integrity and stability. They are typically positioned on either side of the staircase or in the center, depending on the design and configuration of the stairs.


Compare between plinth beam and grade beam?

plinth beam is a part of a structure can transfer loads to the adjacent columns,grade beam is a type of foundation system used to distribute the weight of a building over unstable soil. The grade beam may sit directly on the loose soil.


What is the purpose of the footing of a beam bridge?

The footing carries the entire load of the bridge from the columns up to the foundation so that these loads can be disbursed into the soil. The foundation can be several different things including driven piles or drilled shafts.


How long is a beam routine for grade 14?

it can be as long as you want it to be.. but it can't be more than 3 lengths of the beam


What is the minimum anchorage length for reinforcement?

It is the length of the main bar provided at the column beam junction or column footing junction to allow for the development of stresses to its design strength.


What is the logical application of grade beam foundation construction?

Grade beams works as frame and take the load of slab and diverse to the ground


What is footing wrt civil engineering?

footing is footing and fooot foot foot foot


What is definition of isolated footing and how it design?

Isolated footing Transfers individual column loads directly to the soil. If a single spread footing interferes with another spread footing, the two can be combined to form a combined footing.