answersLogoWhite

0

Copper laminated flexible jumpers are manufactured by stacking high conductivity, electrolytic grade copper foils and then pressure welded. The process is designed in such a way that it enhances the current carrying capacity with almost nil, millivolt drop across the connector. Copper jumpers carry the same current as that of Busbars as they have a constant cross section over the whole length giving a nil millivolt drop. So these kind of jumpers are ideal substitutes for solid busbars. Applications of these jumpers are wide, catering to the many industries like Power Plants, Transformers switchgear's, electricity boards, chemical plants, locomotives, etc.

Flexible jumpers are an excellent and cost effective interconnection for applications requiring flexibility.

Contributed by Bombay Electricals- Manufactureres of Copper Jumpers

User Avatar

Wiki User

14y ago

What else can I help you with?

Related Questions

What size copper main bonding jumper is required based on the service entrance conductors being rated at 250 kcmil thwn-thnn copper?

A size 3/0 AWG copper main bonding jumper is typically required for service entrance conductors rated at 250 kcmil copper. This is based on NEC requirements for sizing the main bonding jumper to be at least 1/10th the circular mil area of the largest service entrance conductor.


How do you do the timing on a 1990 Ford telstar?

Many Fords of that vintage required that a jumper be placed on a socket near the distributor. Without the jumper in place it's not possible to change the timing of the engine. Install the jumper, set the timing with a timing light THEN remove the jumper and it should stay. You'll need to get a reference manual to identify the jumper location and to determine the proper timing advance settings.


What fitting is required to join copper with galvanized pipe?

A threaded copper fitting on the copper side, male or female, and the galvanized is screwed into it.


What size bonding jumper for 200 amp service panel?

There is no bonding jumper wire required on a 200 amp service panel. The meter stack is metallic and is continuous from the mast head down to the distribution panel. If you are talking about the ground wire for a 200 amp panel it requires a #6 bare copper conductor that connects the grounding rod or plate to the neutral point in the distribution panel. Assuming the answer above is an example of a service, where the meter is stacked above the first service disconnect and is mated to this panel by a threaded hub. However if your meter were to be mounted beside your first service disconnect and a metal nipple with lock nuts were used for raceway. You would be required to have a bonding jumper on that nipple sized according to NEC Table 250.122. So for 200 amp that would be #6 copper or #4 aluminum.


What size copper bonding jumper is required by NEC - OR 2011 to bond the gas pipe to a 120v 20A circuit?

I don't know what the NEC - OR 2011 is. Is that a code book for the state of Oregon? The NEC does not allow using a gas pipe as a grounding electrode. You run the risk of heating the gas to explosive temperatures.


How many electrons would be required to deposit 6.35grams of copper at cathode during the electrolysis of an aqueous solution of copper sulphate?

To determine the number of electrons required to deposit 6.35 grams of copper, you need to first calculate the moles of copper deposited using the molar mass of copper. Then, use Faraday's constant (1 mol of electrons = 1 Faraday) to convert moles of copper to the number of electrons. Finally, multiply the number of moles of electrons by Avogadro's number to get the total number of electrons required.


How much energy is required to melt to kilograms of copper?

The energy required to melt 1 kg of copper at its melting point of about 1084°C is approximately 205 kJ. Therefore, to melt 2 kg of copper, you would need around 410 kJ of energy.


How many btu's are required to melt copper?

To melt copper, approximately 1,200 BTUs (British Thermal Units) are required for each pound of copper. This value accounts for both the heat needed to raise the temperature of the copper to its melting point (about 1,984°F or 1,085°C) and the latent heat of fusion. The exact amount can vary slightly based on the specific conditions and purity of the copper.


How much heat energy is required to raise the temperature of 0.365 of copper from 23.0 to 60.0 The specific heat of copper is 0.0920?

To calculate the heat energy required, you can use the formula: Q = mcΔT, where Q is the heat energy, m is the mass of the copper (0.365 kg), c is the specific heat capacity of copper (0.0920 J/g°C), and ΔT is the change in temperature (60.0°C - 23.0°C). First, convert the mass to grams and then plug the values into the formula to find the heat energy required.


How much is required to vaporize 2 kg of copper?

9460 kJ


How many gauge is required of copper wire in multiple generator science project?

34 gauge copper wire will work but to use the 35 gauge copper wire is the best choice


A jumperless motherboard is likely to have one jumper Which jumper is it?

A bios or cmos jumper