answersLogoWhite

0

A threaded copper fitting on the copper side, male or female, and the galvanized is screwed into it.

User Avatar

Wiki User

12y ago

What else can I help you with?

Related Questions

What do you need to connect copper to galvanized pipe?

Yes. Use a threaded fitting, male or female as needed on the copper and screw the galvanized into it.You must use a dielectric fitting to connect copper to galvanized pipe. If you don't, a galvanic reaction will occur and the piping will corrode and leak. You can use a Dielectric Union or a Threaded Brass fitting to join the two types of piping together.UNIONS can leak the best answer would have been a dielectric nipple


What does CXC mean in plumbing terms?

When it comes to a plumbing fitting, description CxC means the fitting is Copper by Copper, or the fitting is used to join two pieces of copper


How to join pvc pipe to galvanized pipe?

You need each piece to have a threaded end fitting, one male, one female.


Is it safe to use copper and galvanized pipes on the same fitting?

No, you cannot join copper and galvy directly. A brass fitting needs to be between the two to prevent electrolysis. You could also use a special type of union that has a gasket between the two halves. It is called a Dielectric union. If this junction is between pipes on your water heater and the cold water supply line, you could use a fitting made for that that also is a back flow preventer (ie a check valve).


How do you join PEX pipe to galvanized pipe?

Yes


Why Using a dielectric union to join galvanized and copper water supply pipes?

Dissimilar metals in contact to each other cause a Galvanic Reaction resulting in one or both metals corroding and causing a leak. A Dielectric Union separates the two metals by uses of rubber and/or plastic thus preventing a Galvanic Reaction. Also in most Plumbing Codes, you can use a Brass fitting in place of a dielectric union as Brass does not react with Copper or Steel Piping (Galvanize Piping).


Can you put copper piping to galvanized piping?

Yes, this happens quite often in older houses, copper pipe can be threaded; thus one can join them and there are several fittings that can be utilized.On the other hand, copper tubing (K, L, M, and DWV) can be joined depending on which of the following application method is used:For copper tubing to galvanized water supply, one would use a dielectric nipple or union to prevent electrolytic action from taking place or dezincification of the galvanizing pipe.If these lines are for waste or venting, the Mission Rubber Company LLC has various types of couplings that can go from tubing OD to pipe OD without the dangers of mixing ferrous and nonferrous metals .For copper tubing to IPS you can solder, braze a male adapter and use the dielectric union, use a copper x galvanized dielectric union, or copper by female adapter and a dielectric nipple .If your connecting to a Durham system and the galvanized pipe has a Tucker coupling or a Kennedy tee wye, then you can use lead and oakum without the fear of mixing dissimilar metals as the lead is nonferrous metal but has no adverse effect with galvanized or copper pipes.


How can I connect copper pipes to PEX pipes in a plumbing system?

To connect copper pipes to PEX pipes in a plumbing system, you can use a push-to-connect fitting or a compression fitting. These fittings allow you to join the two types of pipes securely without the need for soldering or special tools. Simply cut the pipes to the desired length, insert them into the fitting, and tighten the connection according to the manufacturer's instructions. This method provides a reliable and leak-free connection between copper and PEX pipes in your plumbing system.


How can I use the push-to-connect method to join copper fittings securely?

To use the push-to-connect method to join copper fittings securely, follow these steps: Cut the copper pipe to the desired length using a pipe cutter. Ensure the pipe end is clean and free of burrs. Insert the pipe into the push-to-connect fitting until it reaches the tube stop. Check that the pipe is fully inserted by pulling on it gently. Repeat the process for the other fitting. Test the connection for leaks by turning on the water supply. This method provides a secure and reliable connection without the need for soldering or additional tools.


How do you join a smaller Copper pipe to a larger plastic pipe?

all hardware stores sell adaptors to change from copper to plastic. You solder the adaptor to the copper pipe and attach the plastic pipe to this adaptor using screw clamps to tighten the plastic pipe on the adaptor. To be honest. This answer seems like a bush plumbers answer. To be technically correct. In order for you to connect plastic piping to copper piping one fitting is used and it is called a conex fitting, otherwise called cxc fitting. It has a nut and ring on either side of the joint and this type of fitting can be used on either copper or plastic making it ideal. As you tighten the nut the ring inside tightens onto either the plastic or copper making a water tight connection. It is said above that soldering a copper joint and then attaching it to the plastic pipe is the way but in my experience if you try do that, the heat from the soldering will melt the plastic pipe. Take the safer route and more professional route and use conex fittings.


What are pipe fitting used for?

To join lengths of pipe and to route it where it needs to go.


How do you join copper pipe to steel pipe?

Depending if you are talking about stainless steel or galvanised steel. Either way, you need to use copper compression fittings, otherwise known as conex fittings in some countries. Also, you need to be aware of galvanic corrosion if you are connecting copper pipes to galvanized steel pipes. The joint will rot away from the electrolytic action in a few years unless you use a dielectric union or other insulating separation.