answersLogoWhite

0

An offset address is a relative address rather than an absolute address. You use offsets to refer to memory relative to an absolute address. For instance, array indices are implemented using offsets from the start address of the array, such that element 0 is at offset 0 and element 5 is at offset 5.

User Avatar

Wiki User

10y ago

What else can I help you with?

Continue Learning about Engineering

What is use of offset address in 8086 mp?

Offset address is also known as displacement.By adding this offset value to a base address,address of a specific locaction in memory can be accessed


In the Base plus Offset addressing Offset address is also known as?

Base plus displacement.


How would you obtain a far address from segment and offset address of a memory location?

Pointers to far objects are stored using four bytes (32 bits). The bytes are stored little endian or low to high order. The first word contains the 14-bit memory offset (bits 14 and 15 are always 0). The second word contains the page number (or segment number for function pointers). The memory address is calculated as follows: Variable Address = (Page * 0x4000L) + OffsetFunction Address = (Segment * 0x10000L) + Offset


How do you get segmented base and offset when you have logical address?

You cannot. The conversion goes this way: segment+offset -> [segment-table] -> linear_address -> [page-table] -> physical_address PS: In most cases there is only one (4GB long) segment (or one code-segment and one data-segment), so offset is quite the same as linear address


What is Normalization of pointers?

The 8085 had a 16-bit address bus thus it could address a maximum of 64KB of memory (2^16). The 8086 had a 20-bit address bus and could therefore address a maximum of 1MB of memory (2^20). To maintain compatibility, segmented memory was introduced, such that the segment and offset were stored in separate 16-bit registers. In order to perform 20-bit pointer arithmetic upon the 8086, the segment and offset had to be normalised by the compiler to produce a valid 20-bit address. This was achieved by left-shifting the segment by 4 bits and then adding on the offset. The 8086 also introduced the concept of near, far and huge pointers. A near pointer only stores the offset while far and huge pointers store both the segment and the offset. The only practical difference between far and huge pointers is in how pointer arithmetic works. With far pointers, only the offset is affected whereas with huge pointers, both the segment and the offset are affected.

Related Questions

What is use of offset address in 8086 mp?

Offset address is also known as displacement.By adding this offset value to a base address,address of a specific locaction in memory can be accessed


What is the offset for a Class C IP address?

The offset for a Class C IP address is 24 bits.


What is base address and offset address?

In software Engineering KPA denotes.


In the Base plus Offset addressing Offset address is also known as?

Base plus displacement.


Can physical address and virtual address be same?

your question is wrong. it should be "can physical address and logical address be same" answer is no because logical address is the combination of page number and offset whereas physical address is the combination of physical page[frame] and offset


What is the physical address 8086 assembly instruction?

In 8086 assembly language, a physical address is the actual memory address used by the CPU to access data. It is calculated by combining a segment address with an offset address. The segment address is typically stored in one of the segment registers (CS, DS, SS, or ES), and the offset is specified in the instruction. The formula for calculating the physical address is: Physical Address = (Segment Address × 16) + Offset.


How do you calculate instruction address and data address give example?

To calculate an instruction address and a data address, you typically use the base address and an offset. For example, if the base address of a program is 0x1000 and the instruction is located at an offset of 0x0040, the instruction address would be calculated as 0x1000 + 0x0040 = 0x1040. Similarly, if a data item is stored at an offset of 0x0020 from the same base address, the data address would be 0x1000 + 0x0020 = 0x1020.


What is offset in 8086 mp?

displacement from base address


What is the offset in a hexadecimal code?

The offset is usually the difference between the address of a module and the specific location being referenced.


How can one calculate the physical address from a given logical address?

To calculate the physical address from a logical address, you can use the base address and offset. Add the base address to the offset to get the physical address. This process is commonly used in computer systems to translate logical addresses to physical addresses for memory access.


Which register is used as an offset address for the string instruction destination in the microprocessor?

DI is used as an offset address for string instruction destinations in the microprocessors.


What is offset in microprocessors?

Refers to a value added to a base address to produce a second address. For example, if B represents address 100, then the expression,B+5would signify the address 105. The 5 in the expression is the offset.Specifying addresses using an offset is called relative addressing because the resulting address is relative to some other point. Another word for offset is displacement.Ajesh John