answersLogoWhite

0

What else can I help you with?

Continue Learning about Engineering

Is ultimate flexural strength and moment of resistance the same in a reinforced section?

No the moment of resistance is a defining parameter that can be used to calculate the stress in a cross section of a given material that is subject to flexural loading. The ultimate flexural strength is a numerical value of stress at which the material will crack, tear, rip etc. Think about ultimate tensile strength and the value of Young's Modulus. Young's Modulus is not defined at the point of 'necking' and therefore the ultimate tensile strength cannot be computed from Young's Modulus and Hook's Law, but the UTS is an empirically defined value.


Who invented the hook and eye fastener?

The hook and eye fastener was not invented by a single person. It is a simple design that has been used for centuries, and its origins are not attributed to any one individual. The hook and eye fastener has been used in various cultures around the world and has evolved over time.


What is a plumb line hook in an engineer's transit?

A place to hang the line.


What does hook mean in programming language?

A hook is a method of interposing a piece of code in front of another piece of code, so that the first piece of code executes before the second piece of code, giving the first piece of code an opportunity to monitor and/or filter the behavior of the second piece of code. An example might be a mouse hook, allowing the hook code to monitor the mouse while at the same time preserving the functionality of the original mouse event processing routine.


How do you make electrical circuits with 2 or more batteries?

There are 2 ways you can go You can hook them up in series or in parallel If you hook them up in series That is you connect the positive side of the battery to the negative side of the next battery and so on you en up with the voltage being increased by the voltage of each battery So if you hook up a 12 volt battery to the end of a 6 volt battery you end up with 18 volts. Or you can hook them up in parallel That is you hook the abaterys together on one side going from positive to positive and on the other side negative to negative When you do this you end up with the same voltage but increase the amperage.

Related Questions

What is the cargo hook tensile strength of a uh60l?

8000-9000 pounds


What is the cargo hook tensile strength of the UH-60L?

The tensile strength of the UH-60L is 9,000lbs this can be found in FM 3-21.38 chapter 5.


What is the cargo hook tensile strength of the UH-1H?

UH-1H is 4,000 LBS. UH-1N is 500 LBS. Source of data is external loads pathfinder.


What is the cargo hook tinsile strength of the fore and aft combined of the ch47d?

17000 lbs together.


What is Hook to Hook in terms of marine shipments?

Hook to Hook describe the period from the time the cargo comes within reach of a vessel's tackle until the cargo leaves it at the discharging port http://www.m-i-link.com/dictionary/default.asp?term=hook+to+hook


Is ultimate flexural strength and moment of resistance the same in a reinforced section?

No the moment of resistance is a defining parameter that can be used to calculate the stress in a cross section of a given material that is subject to flexural loading. The ultimate flexural strength is a numerical value of stress at which the material will crack, tear, rip etc. Think about ultimate tensile strength and the value of Young's Modulus. Young's Modulus is not defined at the point of 'necking' and therefore the ultimate tensile strength cannot be computed from Young's Modulus and Hook's Law, but the UTS is an empirically defined value.


What is the advantage of using a cargo hook reach pendant?

A cargo hook reach pendant allows the operator to remotely release attached cargo without leaving the cockpit, improving safety and efficiency during loading and unloading operations. It also provides better visibility of the cargo hook and load, reducing the risk of accidents.


What is the tensile strength of copper wire?

to calulate the tensile strength of a copper wire is that get mass/weights, a clamp stand, a g clamp, a copper wire and a boss head. Tie a loop from a wire and hang it on the edge of the clamp stand, put the g clamp on the clamp stando it dosent fall of, anyway after you tie a loop at each ends of the copper wire hook the edge of the weights at the bottom of the loop keep putting on weights until it snaps and make sure you have googles on.


How many types' cargo hook reach pendants are authorized for sling-load operations?

2


What is the advantage of usinga cargo hook reach pendant?

eliminates the use of a static probe man


How many types cargo hook reach pendants are authorized for sling load operations?

2


How many types of cargo hook reach pendants are authorized for slingload?

2 11k lbs and 25k lbls