answersLogoWhite

0

Latch A latch remembers the last state it was told to with another latching

signal Buffer A buffer merely strengthens a signal so that it can

be fanned out with integrity or drive a heftier device. Any amplifier

is a buffer. It outputs a state only as long as the state persists

on its input(s).

User Avatar

Wiki User

17y ago

What else can I help you with?

Continue Learning about Engineering

Difference between SC and LC connector?

One difference between an SC and an LC connector is that an LC connecter is smaller in size than an SC connector. Also, an LC connector is considered a latch connector, whereas an SC connector is considered to be a push-pull connector.


What is difference between single double and circular buffer?

single buffer : you read and write on the same buffer, can be messy if both reading and writing take place at the same time.double buffer : you read one buffer and you write the other one. When both reading and writing are complete, the buffers are swapped. It solves the problem of simultaneous reading and writing but requires synchronization.circular buffer : this a buffer with two pointer : read and write. If both pointers are equal, the buffer is empty.For each write operation, the write pointer advances and each time data is read back, the read pointer advances. It is circular because when a pointer reaches the end, it wraps back to the beginning.It may be used to implement a queue which allows simultaneous reading and writing without synchronization as long as the buffer is not full.A double buffer is basically a circular buffer of size 2 and a single buffer is basically a circular buffer of size 1.


What is latch in 8085?

· A latch remembers the last state it was told to with another latching signal · A buffer merely strengthens a signal so that it can be fanned out with integrity or drive a heftier device. Any amplifier is a buffer. It outputs a state only as long as the state persists on its input(s).


What type of interface circuit is required between the MPU data lines and a 7 segment display?

a latch


What is the difference between technology and process?

what is the difference between license and patent

Related Questions

What is the difference between a buffer and an indicator?

Distinguish between buffer and indicator


What are the difference between buffer stock and safety stock?

no difference


Why a latch is used for an output port but a tri-state buffer can be used for an input port?

The Latch will hold the data until new data will changes from input of Buffer.


What is difference between inverter and buffer?

if you connect Nmos and Pmos other way around then it act as buffer


What is the difference between TAE buffer and TE buffer?

The main difference is in composition. In TE common Tris buffer is bring down to pH 8 with HCl and EDTA is involved but in TAE instead of Tris HCl in TE Tris-acetate buffer is used.


What is the difference between Basel II and Basel III?

There is a main difference between Basel II and Basel III. In Basel III, there is a 4.5% capital buffer to absorb shock. With Basel II, there is no capital buffer.


What is the difference between tbs buffer-tbst buffer and corresponding function of them?

Tween 20. In TBST you add 0.05-0.1/ Tween 20.


What is the difference between gate and latch in digital electronics?

The difference between a latch and a flip-flop is that a latch does not have a clock signal, whereas a flip-flop always does. Apart from the clock signal difference, ~ Latch is a level sensitive device while flip-flop is an edge sensitive device. ~ Latch is sensitive to glitches on enable pin, whereas flip-flop is immune to glitches. ~ Latches take less gates (also less power) to implement than flip-flops. ~ Latches are faster than flip-flops.


Can you use a buffer in place of latch and vice versa in 8085 interfacing?

A buffer is a signal booster that allows you to drive lines with a larger fan-in requirement. A latch is a device that remembers the state of an input line after some point in time. The two are not interchangable.


What difference between 32MB cache buffer and 64MB cache buffer?

A megabyte is a unit of information storage equal to 8,388,608 bits. The cache buffer is an area of extremely fast-access memory used by the processor, so the larger the area, the more data could take advantage of this speed. The "difference" between the two is self-evident.


What is difference with the concentration of phosphate buffer?

The difference in concentration of a phosphate buffer refers to the amount of phosphate salts present in the buffer solution. This concentration can affect the buffering capacity and pH of the solution. A higher concentration of phosphate buffer will provide greater buffering capacity and more resistance to changes in pH compared to a lower concentration.


What is the difference between basel 2 and basel 3?

in basel II there is no capital buffer but in basel III buffer is 4.5 % to be achieved upto jan 16 to absorb the shock