480 v three-phase is a type of supply used in the US for small factories and businesses needing up to a few hundred kilowatts of power. It provides three separate 277 v single-phase supplies and lighting and other appliances are available for 277 v.
480 v split-phase is a different type of supply used in the UK and it is a single-phase supply with a centre-tap on the secondary, supplying two live 240 v lines and a neutral. This type of supply is normally used for a remote group of houses that might be 300-400 yards from a transformer fed from a single-phase 11 kV spur.
A 480 v three-phase system has 480 v between live lines and 277 v from each line to the neutral. This type of supply is common in North America for supplying for example small factories that need more power than a 120/208 v three-phase system can supply.
This 480-v three-phase transformer probably has a 208-v three-phase secondary which has 120 v from each line to neutral. In that case the primary current is 0.433 times as much as the secondary current, so 100 amps in the secondary means 43.3 amps in the primary.
90 kW on 480 volts single phase would be 187.5 amps. On 480 v 3-phase it would be 108 amps.
The most typical three-phase voltage used in China is 380 V.
Current in 200kw at 480 volts = 200,000/480 = 416.667 amps
A 480 v three-phase system has 480 v between live lines and 277 v from each line to the neutral. This type of supply is common in North America for supplying for example small factories that need more power than a 120/208 v three-phase system can supply.
480V.
No, you are billed for the energy used so in principle the voltage does not affect the cost. The equipment used is designed for a set voltage and cannot be used on a different voltage. The reason to choose 480 v instead of 208 v would be based on the size of the site, and if there are distances of more than 300 ft involved in the power supply it might be economical to start with a 480 v system. The choices are between 120/208 v and 277/480 v so that using the higher voltage will require the installation of 277 v lighting
v/i=r so 120/0.25=480 480 ohms is the resistance
Many commercial buildings in the US are supplied with 480 V, three-phase utility power. The phase to neutral voltage of a 480 V system happens to be 277 V. 277 V lighting can be fed directly, eliminating the need for additional transformers and related gear.
It depends on the voltage: 208 v 14 amps, 415 v 7 amps, 480 v 6 amps.
To find out how many times 72 can go into 480, divide 480 by 72. This calculation gives you approximately 6.67, meaning 72 can fit into 480 a total of 6 times with a remainder. Therefore, 72 goes into 480 six full times.
To find out how many times 10 goes into 480, you would perform a division operation. Divide 480 by 10 to get the answer. The result is 48, meaning that 10 goes into 480 a total of 48 times.
what is VVT-I
746 Watts per horsepower / 480 volts x power factor x efficiency x 1.73 = amps assuming that the motor is three phase. 746 x 60 =44760 watts divided by 480 x 1.73 = 53.9 amps ( If the pf and eff. information is not known this will put you in the ball park)
meaning of ang panday by amado v. hernandez
The wattage of the drill can be calculated by multiplying the voltage (120 V) by the current (4 A). Wattage = Voltage x Current Wattage = 120 V x 4 A = 480 watts. Therefore, the wattage of the drill is 480 watts.