0
What else can I help you with?
How many inputs has the NOT gates?
A standard NOT gate will have just one input. It will change its value to the opposite digital value for the output.
What is the opposite of a parallel circuit?
It is not the "opposite" but the major alternative to parallel, which is a series circuit. In parallel circuits, each component has its own circuit path (input to output), while in series the components are connected to one another in a line.
Why terminals of opamp are called as inverting and noninverting?
In an op-amp, an input on the inverting terminal drives the output in the opposite direction, while an input on the non inverting terminal drives the output in the same direction. In a normal closed loop negative feedback configuration, there is feedback from output to inverting input, so that the output becomes a known function of input. So long as you stay within limits, the output will go to whatever value is required to make the inputs be the same.
Why does the output frequency of a full wave rectifier double that of input frequency?
One cycle of the AC input consists of a positive half-cycle followed be a negative half cycle. The FW rectifier basically reverses the polarity of one of the half-cycles, so there are now two positive pulses per single input cycle, effectively doubling the frequency. Of course the rectifier may be wired for the opposite polarity, with two negative pulses per input cycle, but the same principle applies.
Is a touchpad an input device or an output device?
It is an input device.
In what class of levers is the direction of the input force opposite to the direction of the output force?
In a class 3 lever, the direction of the input force is opposite to the direction of the output force. The fulcrum is located at one end, the input force is applied between the fulcrum and the output force, making the output force move in the opposite direction to the input force.
In which type of lever is the direction of the input force opposite of the direction of the output force?
In a second-class lever, the direction of the input force is opposite to the direction of the output force. The input force is applied at one end of the lever, while the output force is generated at the opposite end. Examples of second-class levers include wheelbarrows and nutcrackers.
Working principle of inverter?
If you have a high input going into the inverter it will have a low output and if you have a low input going into the inverter it will have a high output, the bottom line is it's output is the opposite of the input.
What is the difference between the output ofintegratorand input of a differentiator?
A; An integrator will integrate or slowly change as a rapid input is applied. Differentiate will have just the opposite effect
How many inputs has the NOT gates?
A standard NOT gate will have just one input. It will change its value to the opposite digital value for the output.
The difference between upscale and downscale results in an instruments response when subjected to the same input approached from opposite directions is known as?
Hysteresis
What does input force mean in science?
For a rotational output such as a petrol or diesel engine, the force is Torque, which is measured in Foot.pounds or Newton.meters.
What is the opposite of parallel circuits?
It is not the "opposite" but the major alternative to parallel, which is a series circuit. In parallel circuits, each component has its own circuit path (input to output), while in series the components are connected to one another in a line.
What is the opposite of a parallel circuit?
It is not the "opposite" but the major alternative to parallel, which is a series circuit. In parallel circuits, each component has its own circuit path (input to output), while in series the components are connected to one another in a line.
Does a pulley system cause the direction of the output force to be opposite to the direction of the input force?
A pulley system may cause the direction of the output force to differ from that of the input force, but is not guaranteed to do so. In a simple example, a double pulley could easily result in input and output forces in parallel.
What is between the fulcrum and input force on a lever?
The load or resistance is positioned between the fulcrum and the input force on a lever. The input force is applied on one side of the fulcrum, while the load is typically located on the opposite side. The lever uses this arrangement to magnify the force applied to move the load.
A pulley system always causes the direction of the output force to be the opposite of the input force true or false?
False. A pulley system can change the direction of the force applied, but it does not always result in the output force being in the opposite direction of the input force. The direction of the output force depends on the configuration of the pulleys in the system.
