0
What else can I help you with?
What is the maximum DC voltage you could expect to obtain from a transformer with an 18V rms secondary using a full rectifier circuit with a filter capacitor?
25.46V assuming output of transformer is pure sinewave.
What is need of capacitor and resistor in circuit?
because without using capacitor or resistor in a circuit,it cant be complete.Resistor is used to protect the circuit by giving a certain amount of voltage.Capacitor is used to charge and discharge purpose.
When using a step down transformer is amperage affected?
Yes, when using a step down transformer the amperage is affected.
How do you know when you have a circuit?
tuned circuit
Difference between and rcd and an isolating transformer?
An rcd is a device designed to limit duration of electrical shock by disconnecting the circuit when a fault is detected. An isolation transformer is a 1 to 1 (same voltage and current in and out) transformer that keeps one part of an electrical system physically unconnected to another part of the system. It does this by using the principle of a transformer to allow current flow, without actually connecting the load to the source wires.
What is the purpose of the elometer and how does it measure the level of electricity in a circuit?
The purpose of an elometer is to measure the level of electricity in a circuit. It does this by using a sensor to detect the flow of electric current through the circuit and then displaying the measurement on a screen or dial.
Advantage of a transformer over a transformer coupled circuit?
Sounds more like a "homework" or "test" question, rather than a real-world question, and vague, at that! Could you re-phrase your question in a better, more-precise context, or check it for typos? Right now, your question seems to ask "What's the advantage of using a transformer, instead of using a transformer-coupled circuit?"...which makes no sense, since a "transformer-coupled circuit" USES a transformer.
How can you start and stop electric circuit?
You can start an electric circuit by closing the circuit, typically by turning a switch on. You can stop an electric circuit by opening the circuit, usually by turning a switch off or disconnecting a wire.
What are the steps involved in doorbell transformer installation?
The steps involved in doorbell transformer installation are: Turn off the power to the doorbell circuit. Locate the existing transformer or install a new one near the electrical panel. Connect the transformer to the power source using electrical wiring. Connect the transformer to the doorbell system using low-voltage wiring. Test the doorbell to ensure it is working properly. Secure the transformer in place and restore power to the circuit.
Could you build a working electric circuit using glass rods as the conductors why or why not?
Could you build a working electric circuit using glass rods as the conductors? Why or why not?
In a electric circuit does 115 volt using 9 amps have the same power and cost as 230 volt using 4.5 amps?
The cost is about the same using the equation Power= Voltage X Current . However , if the 115 volt electrical circuit is produced from a 230v supply though a transformer , then the transfomer incurs loses and therefore the cost is greater .
Which device controls the flow of electrons in an electric circuit?
Flow of electricity in a circuit is controlled by using 'resistor'.
What type of electric does a home have?
In the US, home electric service is typically 240V AC, 60 hz. The input service is split at the transformer center tap, providing the typical house with either 2 120 VAC circuits or 1 240 VAC circuit, depending on what you're using on a specific circuit. Some other countries use 50 hz.
Can a step down transformer increase current in a DC circuit?
Transformers only work with alternating currents. So the answer is Yes, BUT it would have to be a DC Pulsing circuit. using flip flop circuit or a 555 circuit or chop circuit.
What is the electric potential at this point in the circuit?
The electric potential at a point in a circuit is the amount of electrical potential energy per unit charge at that point. It is measured in volts (V). The electric potential at a point in a circuit can be calculated using the formula V IR, where V is the electric potential, I is the current flowing through the circuit, and R is the resistance of the circuit at that point.
What is the purpose of someone using a electric pallet truck?
The purpose of someone using an electric pallet truck is that it is used to be an electric control water reviser. You use them to pick up big things like cardboard boxes.
What is the maximum DC voltage you could expect to obtain from a transformer with an 18V rms secondary using a full rectifier circuit with a filter capacitor?
25.46V assuming output of transformer is pure sinewave.
