answersLogoWhite

0

According to this site here:

http://www.sizes.com/units/rvalue.htm

3/4" plywood has an R-value of just under 1 (~0.94). The R-value goes significantly up (~2) if one side is reflective (e.g., aluminum surface), I assume the hotter side.

User Avatar

Wiki User

16y ago

What else can I help you with?

Continue Learning about Engineering

Supply lines half inch or three quarters?

Depending what you are wanting to supply. Basin, shower, toilet, bidet, kitchen can be fed with a half inch line Main line and bath can be fed with a three quarter inch line


What is the weight of a four by eight sheet of 0.5 inch drywall?

when asking this question you first need to take into account that plywood comes in different thicknesses therefore weight per particualr thickness of sheet plywood will vary-- in my opinion/ without fact and research / a sheet of 1/2 inch plywood may way about 16 lbs. while a 3/4 inch plywood sheet may way 70 lbs.


What are the cut off lengths or dimensions on 15mm and 22mm low carbon steel pipe?

In the USA, 15mm is half-inch, and 22mm is three-quarters inch. Lengths of pipe nipples in these sizes range from one and a quarter/one and a half, to six inches, in half-inch increments.


What causes your water pressure to drop significantly when more than one faucet is used?

This problem lies with your pipe sizes. If the pipes size of your main line does not equal the supply for demand this will result in the current problem. For example, if your whole house is fed with half inch piping and you open two taps the volume of water has to be shared from the half inch pipe, thus causing a drop in pressure. Whereas if one installed three quarter inch main line "t-ing" off to half inch, because the three quarter inch will hold a higher volume of water when two taps are opened and the water shared, the drop in pressure will be hardly noticeable.


How do you connect a three eighths od plastic water line to a quarter inch standard fridge water line and is there a compression fitting that reduces?

You shouldn't have a problem finding a reducer at a home/builders supply house.

Related Questions

How much weight can a three quarter inch plywood trailer flood hold?

A three quarter inch plywood trailer floor can typically support a distributed load of about 50-60 pounds per square foot. However, the weight capacity may vary depending on the quality of the plywood used and the design of the trailer.


How much does a three quarter inch x 4 x 8 sheet of plywood weigh?

245 lbs


What size of plywood is thicker one quarter inch or three eighth inch?

1/4 = 2/8 so the 3/8 is thicker.


Can ceramic tile be installed over quarter inch concrete backer board rather than half inch if the underlayment is a three quarter inch 7 layer flooring grade plywood?

Yes it can. That seems a very satisfactory way to do it.


What is the price of three quarter inch thick plywood?

that depends on the type of plywood 3/4" ranges from about 20.00 to about 50.00 a sheet (cheap flooring to higher end finish plywood and marine grade pressure treated) in my area. . .check around.


What is the r value of plywood?

¼-inch plywood 0.31 3/8 inch plywood 0.47 ½-inch plywood 0.62 5/8 inch plywood 0.78 This is taken from http://www.sizes.com/units/rvalue.htm, which also has some other materials that could/would commonly be used alongside with plywood to increase the R Value such as building paper and insulation... if both sides of the frame are ply then you must also include the void.


Can ceramic tile be installed over quarter-inch concrete backer board rather than half-inch if the underlayment is a three-quarter inch 7-layer flooring grade plywood?

You did not mention if the three-quarter inch stuff was T&G (tounge and grove), that might make a little difference. I am not an expert in this area but have some personal experiences to share. I was allways told from old school you should have two layers of half inch material one layer turned ninety degrees from the other to give a solid one inch floor. Then you could use the one quarter backerboard and end up with a good tile floor. Then the new school came along and told me i could use one quarter over the T&G three quarter. They said the three quarter T&G was equal to the old style one inch. I tried it with the three quarter and i have several grout cracks and two broken tiles. I was using one quarter quarry tiles six by six. Have now fixed yet but in another room i used three quarter T&G plus another one half inch plywood then one half inch backerboard and same tiles no cracks.


Can you shoot two and three quarter inch shells in a shotgun marked two and three quarter or three inch?

Yes


What is better three quarter inch heel or half inch heel?

---- ---- ----


What is 8 cm?

about three and a quarter inch.


What is a quarter of a inch thousandths?

A quarter of an inch is equal to 0.25 inches. To convert this value to thousandths, we multiply 0.25 by 1000, as there are 1000 thousandths in an inch. Therefore, a quarter of an inch is equal to 250 thousandths of an inch.


Game played with a half inch to three quarter inch ball?

roulette