In series like so ---6 ohms ---- 12 ohms --- , the total resistance is just 6 ohms + 12 ohms.
assuming you mean in parallel like this:
_|---6 ohms-----|
-|~|-
_|---12 ohms---|
then the resistance of this can be calculated like so:
1/6 ohms + 1/12 ohms = 1/R (where R is the resistance of the circuit as a whole)
2/12 ohms + 1/12 ohms = 1/R
3/12 ohms = 1/R
1/4 ohms = 1/R
so R = 4 ohms
A few notes, if the resistors are in parallel the total resistance will always be less than or equal to the lowest resistance in parallel (i.e 6 ohms in parallel with 12 ohms will have resistance less than 6 ohms).
Also if two resistances in parallel are the same, then the resistance is half of the resistance of both resistors (i.e. 1/2 ohms + 1/2 ohms = 1/R; 1 = 1/R, R=1 ohm which is half of 2 ohms).
This process can be extended to 2 or more resistors in parallel.
i.e if we had a 6 ohm, 6 ohm and 12 ohm resistor in parallel we could go
1/6 ohms + 1/6 ohms + 1/12 ohms = 1/R
(1/6 ohms + 1/6 ohms) + 1/12 ohms = 1/R
1/3 ohms + 1/12 ohms = 1/R
4/12ohms + 1/12 ohms = 1/R
5/12 ohms = 1/R
so R = 12/5 ohms or 2.4 ohms
1). 6V battery, 1-ohm resistor, 2-ohm resistor, all in series:Total resistance = 3 ohms.Current in the loop = 6/3 = 2 amperesPower dissipated by the 2-ohm resistor - I2R = 8 watts.2). 4V battery, 12-ohm resistor, 2-ohm resistor, all in parallelThe 12-ohm resistor is irrelevant.4 volts across the 2-ohm resistor.Power dissipated by the 2-ohm resistor = E2/R = 8 watts.
The formula you are looking for is I = E/R. Amps = Volts/Resistance. If you say it is normally a 2 Amp circuit, it normally draws 2 amps. Therefore the original resistance offered to the 12v battery is 2/12 = 6 Ohms. If you then connect a 12 Ohm resistor in series, they are added, so R = 18 Ohms. Now if you put 12v across this circuit it will draw 12/18 = 0.66 Amps. Or If you just put a 12 Ohm resistor across the 12v supply it will draw 1 Amp. If the circuit is protected by a 2 Amp fuse, it will not blow, but the resistor will get hot.
Resistor values are given in ohms. A value may be selected to deliver a specific current at a given voltage. This is given in what is known as Ohm's Law where: Voltage (V) = Current (A) X Resistance (Ohm) A 12ohm resistor placed across a 12V battery would pass 1Amp of current and put out 12W of heat.
Resistor values are given in ohms. A value may be selected to deliver a specific current at a given voltage. This is given in what is known as Ohm's Law where: Voltage (V) = Current (A) X Resistance (Ohm) A 12ohm resistor placed across a 12V battery would pass 1Amp of current and put out 12W of heat.
P= I*E E= I*R i=e/r P= e*e/R 120w*12ohm =sqrt(1440) v = 37v but remember the filament is not running at room temperature a 100W 120V bulb may measure less than 12ohms but it is 144 ohms when at 5600K