answersLogoWhite

0

On a three phase system with a line to line voltage of 13800, a wye connection will give you a voltage of, 13800/1.73 = 7977 volts to ground.

User Avatar

Wiki User

10y ago

What else can I help you with?

Continue Learning about Engineering

Can you use an oscilloscope to measure the 110 volts AC in a home wall outlet if so how is it done safely to avoid damage to the oscilloscope?

The first thing to consider in measuring the line voltage of a home wall outlet is the oscilloscope probe voltage rating. Most high-impedance probes have a resistance of one Megohm of greater and will withstand peak voltages in excess of 200 Volts, but it pays to make sure that you do not damage the resistor within the probe. The next item of concern is the current flowing in the power line ground. If you have a ground current protected outlet, then it will be safe from dangerous ground currents. It will also limit the voltage errors produced by any circulating ground currents. As is the case for many instruments, the metal case is generally tied to the line common through a small capacitor, so the ground current can produce a small voltage between the case and line common. That is the purpose of using a line current interrupter for protection. Do NOT connect the oscilloscope ground lead to the line socket. If you connect it to the wrong pin, then the case can be at a high enough voltage to cause shock. Better to be on the safe side. Keep in mind that the voltage is rating in RMS (root-mean-square) volts and not peak or average volts. Therefore, the sine wave peak is 1.414 (square root of 2) times the RMS voltage. Conversely, the RMS voltage the peak voltage divided by 1.414.


In a 3 phase 480 panel what voltage should you get phase to phase?

The voltage you are referring to is a 'line-to-line' voltage ('line voltage'), as there is no such thing as a 'phase-to-phase' voltage.480 volts. In real life, the voltage will vary slightly by up to 3% (14 V) on a properly sized circuit. Line to neutral will measure 277 volts, plus or minus 3%.


Does line to ground voltage always half the value of line to line voltage?

Line to Ground voltage = line to line voltage / 1.73AnswerIt depends what configuration is being measured. In the case of the secondary of a split-phase distribution transformer used to supply residences in North America, the answer is yes. In the case of a star (wye) connected secondary distribution transformer used to supply residences in Europe, no: the line to ground voltage will be as described in the first answer.


How do you calculate 440v phase?

Let's get the terminology correct. A 'phase voltage' is measured across a phase, whereas a line voltage is measured between two lines. So there is no such thing as a 'phase to phase' voltage -it's a line to line voltage (hence the term 'line voltage').


Why do you have voltage to ground but not voltage phase to phase?

There is phase to phase voltage in 3 phase system.AnswerYou don't get voltage 'phase-to-phase'; it's 'line-to-line'!

Related Questions

What voltage would be measured from any phase to ground on a 480 volt 3 phase wye system?

A voltage of 277 is the line to neutral (ground) voltage of a 480 volt wye three phase system. L1- N, L2 - N and L3 - N will give you 277 volts. L1 to L2. L2 to L3 and L3 to L1 will give you 480 volts.


What is the voltage of a telephone line?

48 VOLTS


Why does ac line voltage read 185 volts?

I checked with my other meter and get 120 volts!


What is the voltage between neutral and earth if neutral is broken?

Normally, it is zero.Except in very special cases, the neutral and ground (earth) conductors in a building are tied together at one point in the system, so ideally the voltage difference would be zero. The reason that it might not be zero is there is current flowing in the neutral and, thus, voltage drop in the neutral conductor. Since the ground conductor normally never has current flow (unless there is a fault), there will be a difference in voltage equal to the voltage drop across the neutral conductor, which varies with load (current).It should be 0V , but as per our earth pit maintaining that voltage will be varied even also not exceed 5V.


Is it normal to have a 220 volts from line to ground?

In England and Europe yes, 240 volts is the star point voltage of a 416 volt three phase four wire system. In North America no, it is not normal to have 240 volts to ground. On a single phase system that is used in homes it should only be 120 volts. In control panels that use 240 volts as a control voltage and one side of the control transformer is taken to ground, only then would you find the 240 to ground. This connection is used to trouble shoot the control panel by allowing one of the voltage tester leads to be connected to ground while the other lead can be used to probe for voltages at terminal points.


Why 380 volts line to line if connect line to neutral is 220 volts?

A voltage of 380 volts is a three phase voltage. On a three phase four wire system, each phase leg to neutral (grounded) will give you 220 volts. This voltage is obtained by dividing the phase voltage by 1.73, as the phase legs are generated 120 degrees from each other. Square root of three is 1.73 divided into 380 equals 220 volts.


Why does 220 volt line put out 250 volts?

A 220 volt line may put out 250 volts because this specification features voltage that varies between 220 and 250 volts. In other countries, the electricity varies in voltage between 110-120 volts.


In a 480 Volt 3-phase power supply what is the voltage between each lead?

Assuming this is a WYE connected system: (Most commercial/industrial services are) Your question answered it: 480 volts. The phase to phase voltage on this system is 480 volts and the phase to ground voltage is 277 volts.AnswerThe 'leads' you refer to are more-properly called 'lines', and the voltage between any pair is called a 'line voltage' (not a 'phase voltage', as stated in the original answer). The rated voltages of three-phase systems, regardless of whether they are three-wire (delta) systems or four-wire (star/wye) systems are always quoted in terms of their 'line voltages'. So, to answer your question, the line voltage ('voltage between leads' ) of your three-phase system is 480 V. If your system is a four-wire star/wye system, then the phase voltage voltage, or 'line-to-neutral' (not 'phase to ground') voltage is the line voltage divided by 1.732, i.e. 277 V.


What is HT transmission line voltage in Punjab?

approx. 1000 volts


Can you use an oscilloscope to measure the 110 volts AC in a home wall outlet if so how is it done safely to avoid damage to the oscilloscope?

The first thing to consider in measuring the line voltage of a home wall outlet is the oscilloscope probe voltage rating. Most high-impedance probes have a resistance of one Megohm of greater and will withstand peak voltages in excess of 200 Volts, but it pays to make sure that you do not damage the resistor within the probe. The next item of concern is the current flowing in the power line ground. If you have a ground current protected outlet, then it will be safe from dangerous ground currents. It will also limit the voltage errors produced by any circulating ground currents. As is the case for many instruments, the metal case is generally tied to the line common through a small capacitor, so the ground current can produce a small voltage between the case and line common. That is the purpose of using a line current interrupter for protection. Do NOT connect the oscilloscope ground lead to the line socket. If you connect it to the wrong pin, then the case can be at a high enough voltage to cause shock. Better to be on the safe side. Keep in mind that the voltage is rating in RMS (root-mean-square) volts and not peak or average volts. Therefore, the sine wave peak is 1.414 (square root of 2) times the RMS voltage. Conversely, the RMS voltage the peak voltage divided by 1.414.


In a 3 phase 480 panel what voltage should you get phase to phase?

The voltage you are referring to is a 'line-to-line' voltage ('line voltage'), as there is no such thing as a 'phase-to-phase' voltage.480 volts. In real life, the voltage will vary slightly by up to 3% (14 V) on a properly sized circuit. Line to neutral will measure 277 volts, plus or minus 3%.


Does your house have 440 volt line?

No houses are wired for 440 volts. In the USA, most houses are wired for 240/120 volts called single or split phase. That means each "leg" of the service is 120 volts to ground, but across the two it sums to 240 volts, since each "leg" is 180 degrees out of phase with respect to each other. When one "leg" of the service is at +120 volts, the other "leg" is its mirror image, at -120 volts. In this way, connecting across the two yields twice the voltage of either leg to ground, allowing the use of 240 volt or 120 volt appliances depending on how connected- to ground or across "legs". Most other countries with 220-240 volt appliances do not use split phase service. There is only the one phase to ground and in those countries the incoming line is 220-240 volts to ground, voltage depending on the country.