answersLogoWhite

0

There are too many to list. For example wrought low alloy steel like 4130, or 1/2 hard stainless 301 all exceed that value

User Avatar

Wiki User

12y ago

What else can I help you with?

Continue Learning about Engineering

Which one is greater yield strength or breaking strength?

The breaking strength is always greater than the yield strength.


Can the Yield strength of steel ever be greater than the Ultimate tensile strength?

The yield strength is reached when the material becomes non - linear ( that is non elastic) and takes a permanent set when load is released. Material stretches but does not break. Ultimate strength is when it breaks and is higher than yield strength.


What is the yield strength of deformed steel bars?

The yield strength of deformed steel bars, commonly used in construction, typically ranges from 250 MPa (megapascals) to 600 MPa, depending on the grade of the steel. For example, grade 40 deformed bars have a yield strength of approximately 280 MPa, while grade 60 bars have a yield strength of about 420 MPa. The specific yield strength can vary based on the standards and specifications of the manufacturer and the region. Always refer to relevant codes and standards for precise values.


What are the characteristics of construction steel?

Yield strength is the most common characteristic of construction steel, it has a minimum yield strength of 275 N/mmâ_. Steel is also very tough and durable, it can withstand extremely heavy loads. It is also weldable and ductile.


What is the ultimate stress of mild steel?

Allowable stress would normally refer to design using Allowable Strength Design, also known as working strength design. In this the allowable stress is usually a fraction of the yield strength and can be different for uniform tension and bending. Typically mild steel has a yield strength of about fy=250MPa with allowable stresses in Tension, 0.6fy=150MPa Bending, 0.66fy=165MPa

Related Questions

Which one is greater yield strength or breaking strength?

The breaking strength is always greater than the yield strength.


Is tensile strength of cold rolled steel is greater than yield stress?

For ductile materials, the yield stress is always lower than the tensile strength of the material. For brittle material they can usually be considered the same point. Steel is generally considered ductile.


What is Characteristic yield strength of steel in terms of minimum yield stress and percent proof stress?

what is characteristic yield strength


What is yield strength and tensile strength of 20c8 cast steel?

YIELD STRENGTH 242 N/sqmm TENSILE STRENGTH 440~520 N/sqmm


Can the Yield strength of steel ever be greater than the Ultimate tensile strength?

The yield strength is reached when the material becomes non - linear ( that is non elastic) and takes a permanent set when load is released. Material stretches but does not break. Ultimate strength is when it breaks and is higher than yield strength.


What is the tensile and yield strength of S275jo steel?

275 MPa


What is the minimum yield strength of S235 steel?

It is its yield stress which is equal to 235 N/mm2


Is there a general rule for yield vs tensile strength in steel?

yield is the breaking point and tensile strength is what it is rated at per square inch


What is the endurance limit for cold roled steel?

0.5 of the yield strength.


What is the formula to calculate the yield moment for a column?

My= As*Fy*Jd As= Area of steel reinforcement (tensile steel only) Fy= yield strength of steel Jd= moment arm


What is the yield strength of deformed steel bars?

The yield strength of deformed steel bars, commonly used in construction, typically ranges from 250 MPa (megapascals) to 600 MPa, depending on the grade of the steel. For example, grade 40 deformed bars have a yield strength of approximately 280 MPa, while grade 60 bars have a yield strength of about 420 MPa. The specific yield strength can vary based on the standards and specifications of the manufacturer and the region. Always refer to relevant codes and standards for precise values.


What is difference between A36 steel and 44W steel grade 300w?

A36 steel is a standard mild steel grade with a minimum yield strength of 36,000 psi, while 44W/300W is a Canadian steel grade with a minimum yield strength of 44,000 psi. The main difference lies in the yield strength, with the 44W/300W grade being stronger and more suitable for structural applications that require higher strength.