Since inductive reactance is 90° out of phase from pure resistance, this can be calculated like the hypotenuse of a right triangle. Sqrt( 172 + 62) = 18.028 Ω
The angle is 70.6° lagging.
the net oppostion offered by the rlc circuit for the ac current to pass through it is called the impedance of rlc circuitAnswerThe impedance of an RLC circuit is the vector sum of the circuit's resistance, inductive reactance, and capacitive reactance, expressed in ohms.
The load current will lag the supply voltage by an angle called a 'phase angle', determined by the values of resistance and inductive reactance. The magnitude of the load current will be determined by the impedance of the circuit, which is the vector sum of the resistance and inductive reactance.
Impedance relays are used whenever over-current relays do not provide adequate protection. They function even if the short circuit current is relatively low. The speed of operation is independent of current magnitude. Impedance relays monitor the impedance between the relay location and the fault. If the impedance falls within the relay setting, the relay will operate. The basic construction for impedance relays on which the principle of operation is easily explained is the balanced beam.
ALL resistance are conductors. just the magnitude value changes
The same as what? when an inductor is connected in series with a resistor and a current passed through them, the voltages across the resistor and inductor are equal when the reactance is equal to the resistance: 2.pi.f.L = R
the net oppostion offered by the rlc circuit for the ac current to pass through it is called the impedance of rlc circuitAnswerThe impedance of an RLC circuit is the vector sum of the circuit's resistance, inductive reactance, and capacitive reactance, expressed in ohms.
The load current will lag the supply voltage by an angle called a 'phase angle', determined by the values of resistance and inductive reactance. The magnitude of the load current will be determined by the impedance of the circuit, which is the vector sum of the resistance and inductive reactance.
A changing current through an inductor induces a voltage into the inductor, the direction of which always opposes the change in that current.So, in a d.c. circuit, an inductor will oppose (not prevent) any rise or fall in current, although the magnitude of that current will be determined by the resistance of that inductor, not by its inductance.In an a.c. circuit, because the current is continuously changing both in magnitude and in direction, it acts to continuously oppose the current due to its inductive reactance. Inductive reactance is proportional to the inductance of the inductor and the frequency of the supply. The vector sum of the inductive reactance of the inductor and the resistance of the inductor, is termed the impedance of the inductor. Inductive reactance, resistance, and impedance are each measured in ohms.
Impedance is a vector quantity because it has both a magnitude and a phase angle associated with it. The magnitude represents the resistance and reactance components, while the phase angle accounts for the relationship between the current and voltage in an AC circuit.
Real part = (magnitude of total impedance) x (cosine of the angle) Imaginary part = (magnitude of total impedance) x (sine of the angle)
Impedance is expressed in units of 'ohms'.In a DC situation, impedance is simply the scalar resistance.In a circuit where voltage/current have time-varying components,impedance is a complex quantity, with both magnitude and angle.
a circuit in which inductance L,capacitance C and resistance R are connected in series and the circuit admits maximumum current corresponding to a given frequency of a.c.Another AnswerIn the case of a series circuit, resonance occurs when its inductive reactance is exactly equal to its capacitive reactance. As the vector sum of these two quantities will then be zero, the only opposition to current will be resistance and, so, maximum current will flow through the circuit when resonance occurs. ALL circuits can be made to resonate at what is called their 'resonant frequency' because, as frequency increases, the inductive reactance increases but capacitive reactance falls -so, at some point the two will equal each other, and resonance will occur.In my view resonance means - the condition that exists when the inductive reactance and the capacitive reactance are of equal magnitude, causing electrical energy to oscillate between the magnetic field of the inductor and the electric field of the capacitor.
In the case of AC, you can express the current, the voltage and the equivalent to the resistance (called "impedance" in this case) as a vector - with a magnitude, and a phase angle.
It is the complex ratio of the voltage to the AC (alternating current) circuit. It extends the concept of resistance to AC circuits due to magnitude and phase.
In a DC circuit, it's the branch with the largest resistance. In an AC circuit, it's the branch with the largest magnitude of impedance.
According to maximum power transfer theorem for ac circuits maximum power is transferred from source to load when the load resistance is equal to the magnitude of source impedance. The source imoedance is the thevenin equivalent impedance across the load
Impedance relays are used whenever over-current relays do not provide adequate protection. They function even if the short circuit current is relatively low. The speed of operation is independent of current magnitude. Impedance relays monitor the impedance between the relay location and the fault. If the impedance falls within the relay setting, the relay will operate. The basic construction for impedance relays on which the principle of operation is easily explained is the balanced beam.