0
What else can I help you with?
What does it mean when motor ticks?
i have a metal sleeve over each spark plug wire at the motor.....cant get the wire out to get to the plugs?? how do i get the wire off the plug??
Why doesn't my 300d Mercedes fan work?
Disconnect the plug to your fan. Hook a jumper wire to ground the negative wire and a hot wire to the positive wire. If the fan doesn't work, then you can buy one on Ebay or other sources.
How do you convert a purchased ceiling light fixture that is meant to be hardwired to a swag light that will plug into the wall?
Get enough new wire for the length needed and the link chain to make the swag. Attach the new wire color to color and cover tightly with electrical tape. (Better to solder first if you can) Try to tuck the taped connections close to the fixture to hide. Then thread the new wire thru the chain and purchase a separate plug. The plug will have a place to attach the wires to screws and a cover that snaps over the wire. You're ready to plug in.
Can MCB switches be used for Geysers?
Connect a good quality three pin, 15 amps plug the geyser cable with green wire connected to the earth terminal (thicker pin in the plug). If the geyser is to be fitted permanently at one location only, then it is advisable to connect it with a D.P. Switch to avoid burning of wires due to loose connections in three in plug and socket.
What type of plug is suitable for figure 8 cable size?
A figure 8 cable typically requires a figure 8 plug, commonly known as a C7 or C8 connector. This type of plug is designed to fit the flat, two-wire configuration of the figure 8 cable, which is often used for various electronic devices like radios and some small appliances. Ensure that the plug matches the voltage and current requirements of your device for safe operation.
How do you wire a three prong plug that has a horizontal prong?
Depends upon which prong is horizontal. Under NEMA standards (in the USA) it could either be 250v (6-20p) with both non-grounded terminals hot, or 125v (5-20p) with the horizontal being neutral. Obviously, WHICH terminal is horizontal determines the possible voltage, so you cannot accidentally plug a 125v device into a 250V socket.
Can you properly switch prongs on a 20 amp 250v twist lock to change it to a 125v?
No, it is against the National Electrical Code to wire a receptacle with the wrong voltage. You should call a qualified electrician to change the 250V receptacle to a 125V receptacle.
What does it mean if your car jumps after getting a tuneup?
Spark plug wire not connected to spark plug? Spark plug wire connected to Wrong spark plug? Vacuum line disconnected? Bad spark plug or wire?
Which wire is not present in a 2 pin plug?
In a 2-pin plug, the wire that is not present is the grounding wire. This type of plug only has two prongs for the live and neutral wires, unlike a 3-pin plug that includes a grounding wire for added safety.
Is a T100L 250V fuse the same as a T100mA 250V fuse?
It should be the same thing. But other things are also described as T100L so you should make sure it's a fuse and check by holding it up to the light that it has a very thin wire inside the glass tube.
What would cause one spark plug wire to arc to the engine at the spark plug boot?
bad spark plug wire.
How do you change a four wire plug to a three wire plug?
I need a lot more information. I don't know what you mean by four wire plug. What does it look like, what was it used for? What three wire plug are you installing, what does it look like, what is it used for. What color ore the wires?
I have a1982 Chevrolet 305 and wan't to know were does the longies plug wire go?
to the furtherest plug! Plug #1 is probably the longest wire
How do you remove a spark plug wire on a toro lawn mower?
how to replace plug wire on a toro mower
Why would a 1996 Suzuki Sidekick jx not start unless you remove one spark plug wire?
If it is the same plug every time, I would say the plug or wire is grounding out some where. Try replacing the plug the the wire.
Will a 2 pole wire work with a 3 pole plug?
A 2-pole wire will not work on a 3-pole plug. You will need to use a 3-pole wire on a 3-pole plug.
How do you wire a 3 wire 240 volt stove to a 240 volt 4 wire feed?
Change the cord/plug on the stove to a four wire cord/plug. When installing the new plug remove the grounding strip that connects the center lug in the stove wiring block to the frame of the stove. Connect the white wire from the new plug to the center lug. Connect the green wire from the plug to the stove frame.
