0
What else can I help you with?
Minimum distance below sink to trap?
What is the minimum distance between the bottom of a sink and the trap attachment for a bathroom sink
Who invented the P-trap?
Who invented the p trap
Can you use the existing shower drain for a pedestal sink and do you need a trap for the sink since there is already a trap in the floor?
No and yes. Amendment (not from a professional plumber!): If you were simply running the sink drain into the shower drain and if there was not a reduction in pipe size, I would think you would be able to do that. I think the reason you need a trap for the sink has to do with code that requires a trap be no more than 24" from the basin to the trap arm. That being said, the pedestal sink in my house does not have a trap until after it drains below the floor.
Where is a p-trap located?
Directly under each sink.
How do you replace a sink drain?
Depends on the mateiral you already have (PVC) Galvanized nippe and brass P trap or rough brass connectiong to the trap and then of course what size of drain basin, KS, Slop Sink
Is your sink trap leaking and in need of repair?
Is your sink trap leaking and needs fixing?
Minimum distance below sink to trap?
What is the minimum distance between the bottom of a sink and the trap attachment for a bathroom sink
What are the different parts of a sink trap?
A sink trap typically consists of three main parts: the U-shaped trap bend, the trap arm, and the trap adapter. The U-shaped trap bend holds water to prevent sewer gases from entering the house. The trap arm connects the trap bend to the drain pipe, and the trap adapter connects the trap to the sink's tailpiece.
What are the steps to properly install a p-trap assembly in a sink?
To properly install a p-trap assembly in a sink, follow these steps: Remove the existing p-trap assembly, if applicable. Place the new p-trap under the sink drain. Connect the trap arm to the sink drain and the trap bend to the trap arm. Tighten the slip nuts with pliers to secure the connections. Check for leaks by running water through the sink. Make adjustments if needed to ensure a proper seal. Test the sink again to confirm the p-trap is installed correctly.
How can I create a flexible trap for my sink?
To create a flexible trap for your sink, you can use a P-trap with adjustable joints that can be easily adjusted to fit the specific dimensions of your sink. This will allow for flexibility in installation and maintenance.
Who invented the P-trap?
Who invented the p trap
How do you install a P-trap under a sink?
To install a P-trap under a sink, first, remove the existing trap. Then, connect the new P-trap to the sink drain and the wall pipe using slip-joint nuts and washers. Make sure the trap is properly aligned and secure all connections. Finally, check for leaks by running water through the sink.
Can you use the existing shower drain for a pedestal sink and do you need a trap for the sink since there is already a trap in the floor?
No and yes. Amendment (not from a professional plumber!): If you were simply running the sink drain into the shower drain and if there was not a reduction in pipe size, I would think you would be able to do that. I think the reason you need a trap for the sink has to do with code that requires a trap be no more than 24" from the basin to the trap arm. That being said, the pedestal sink in my house does not have a trap until after it drains below the floor.
What is the purpose of a p trap in a kitchen sink?
The purpose of a p-trap in a kitchen sink is to prevent sewer gases from entering the house and to trap debris that could clog the plumbing system.
When were bear trap invented?
the bear trap was invented in the 17th century
How can I remove a sink trap?
To remove a sink trap, first place a bucket underneath to catch any water. Loosen the slip nuts on both ends of the trap using a wrench. Carefully remove the trap and clean out any debris. Reattach the trap by tightening the slip nuts. Check for leaks before using the sink again.
What is the purpose of a p trap in a bathroom sink?
The purpose of a p-trap in a bathroom sink is to prevent sewer gases from entering the room and to trap debris that could cause clogs in the plumbing system.
