answersLogoWhite

0

Backward diode

User Avatar

Wiki User

12y ago

What else can I help you with?

Continue Learning about Engineering

Can you use resistance in place of diode in clipping circuits?

no we not use resistance in place of diode.


Why you use negative source in emitter biasing?

to get the base- emitter junction forward bias we should connect the negative of the diode with the negative of the battery and the positive of the diode with the positive of the diode so we should connect negative source in the emitter


How do you test diode?

To test a diode, you can do a variety of tests. The easiest may be measuring the resistance across the leads of a diode. One side should read very high resistance, over 1 megohm, while the other should read a moderate amount of resistance, maybe a few hundred thousand ohms. This is a sign that a diode works. If both sides read very high resistance, the diode is open. If both sides read very low resistance, then the diode is shorted.


Why does a SCR have negative resistance?

Whenever you measure resistance, the resistance itself cannot be negative!When an SCR (Semiconductor Controlled Rectifier) is not conducting, it has a high resistance between its anode and its cathode. When its gate is triggered and the SCR is conducting, it has a low resistance between its anode and its cathode.For more information about SCRs, see the answer to the Related Question (for which a link is shown below) and also the Related Link.


Why resistance use in silicon diode characteristics?

Resistance is used in characterizing silicon diodes, or any component for that matter, because the equivalent resistance in a certain condition tells you what the circuit will do in that condition. It is true that a diode is not a resistor, but it has an equivalent resistance at each point on it operating curve. Let take three points, for example... With one ampere of current, the forward voltage might be 0.68 volts. That corresponds, using Ohm's law, to a resistance of 0.68 ohms. With ten amperes of current, the forward voltage might be 1.15 volts. That corresponds to a resistance of 0.115 ohms. With 25 amperes of current, the forward voltage might be 1.7 voltage. That corresponds to a resistance of 0.068 ohms. You can obtain the forward resistance curve from the manufacturer's data sheet. Even if there is only a voltage versus current curve, you can calculate resistance using Ohm's law. You need to know the resistance curve in order to design the circuit that uses the diode. In high performance situations, such as in large power supplies, the resistance of the diode may well be critical, and would therefore be a factor in selecting which diode amongst several choices to choose.

Related Questions

Can you use resistance in place of diode in clipping circuits?

no we not use resistance in place of diode.


Why you use negative source in emitter biasing?

to get the base- emitter junction forward bias we should connect the negative of the diode with the negative of the battery and the positive of the diode with the positive of the diode so we should connect negative source in the emitter


How do you find the ac resistance of a diode?

The ac resistance of a diode is found using the equation: (The change in Vd)/(The change in Id) An easier was is to use the Equation: 26mV / Id. This is a general form as the ac resistance of a diode change as the temperature changes.


How do you check if a diode is serviceable?

use a vomm set to infinite resistance if you have reistance one way and not the other way. diode is good (must be isolated from circuit) if no resistance both directions diode D.O.A.


Is it necessary to add a series resistance with the diode or not?

if the diode is forward biasedwell practically the current flows in a circuit if and only if an effective resistance is present in the circuit, if we consider the diode to be ideal (barrier potential but no internal resistance) in this case an external resistance is required if we use the approximate model (both barrier potential and internal resistance are considered) we need not use an external resistance the internal resistance itself acts as the effective resistance.if the diode is reverse biased:-the same explanation applies even if the diode is reverse biased but one must take care that the reverse voltage drop on diode should not increase the peak inverse voltage mark the diode would be burnt or damaged if this phenomena occurs.So this can be prevented by adding suitable resistance to the circuit through which the voltage drop on diode can be managed


Why resistance is use in circuits?

To prevent excess voltage to enter in a diode or LED etc


How do you test diode using multimeter?

A Diode will pass the electrical current into one direction, and will produce high resistance in the opposite direction. To check a diode, use an Ohm-Meter or a "multi meter", and set to measure resistance "Ohm", in the 1k Scale. You will have two leads in the ohm meter + and - (Red and Black) If you measure the resistance in one direction ( red lead touching one of the diode leads , and the black is touching the other lead ) , and you found a low resistance in one direction, and a very high resistance in the other direction ( by reversing the red/black leads) , this diode should be ok. If you find low resistance in both directions, this diode is shorted, and is damaged If you find high resistance in both directions, this diode is open circuit, and is damaged


How do you test diode?

To test a diode, you can do a variety of tests. The easiest may be measuring the resistance across the leads of a diode. One side should read very high resistance, over 1 megohm, while the other should read a moderate amount of resistance, maybe a few hundred thousand ohms. This is a sign that a diode works. If both sides read very high resistance, the diode is open. If both sides read very low resistance, then the diode is shorted.


How will differentiate silicon and germanium diode from a group of diodes?

Simple, Use the multi-meter , switch to the diode option then connect the positive wire to the positive of diode n negative to the negative ( +ve wire red, -ve wire black) if the there is a reading of =~0.7V then it is silicon. and if it is =~ 0.3V then it is germanium.


Why does a SCR have negative resistance?

Whenever you measure resistance, the resistance itself cannot be negative!When an SCR (Semiconductor Controlled Rectifier) is not conducting, it has a high resistance between its anode and its cathode. When its gate is triggered and the SCR is conducting, it has a low resistance between its anode and its cathode.For more information about SCRs, see the answer to the Related Question (for which a link is shown below) and also the Related Link.


What happens if a silicon diode measures high value of resistance with the meter leads in both positions?

If the meter is developing more than the necessary forward breakdown voltage of the diode, typically 0.7 volts, then the diode is bad. However, some meters do not generate enough voltage in resistance mode to bias the diode on, unless you flip a switch that enables diode test mode. Use another meter at the same time to measure the voltage across the diode and compare that with the diode's published forward breakdown voltage.


How do you identify the polarity of a diode when the tester is on diode scale?

Connect the positive lead of the tester to the anode of the diode and the negative lead to the cathode. If the tester displays a voltage drop or a forward bias reading, the diode is forward biased and the anode is positive. If the tester displays an OL or reverse bias reading, the diode is reverse biased and the anode is negative.