0
Actually, it depends on the resistance of the other components in the circuit, and not so much on whether or not the total circuit current is low or not. Often, conductor resistance is ignored because it is so much lower than the active components that it does not matter. In a circuit with low resistance components, however, conductor resistance can be important, even if the total current is relatively low, because the voltage drop over the wire becomes a significant part of the overall circuit.
To answer the specific question, even though its slightly misleading, conductor resistance does tend to become important in high current circuits because the voltage drop over the conductor (Ohm's Law: Voltage is current times resistance) can become high. Even in high current circuits, however, if the conductor is substantially less resistive than the components, the tendency is still to ignore it, except that you have to account for heating of the conductors along with heating of the components.
What else can I help you with?
What is an over-current protective device?
That is called a fuse. A fuse is a protective device, which will interrupt the flow of electricity if it is subjected to a current that is greater than its rating. Some fuses are designed to handle a large inrush of current and are used in circuits such as air conditioners, where a large amount of current is needed at startup, for a short duration and then current drops to a lower level. These are sometimes called time-lag fuses.
When cells are connected in parallel then?
putting cells in series gives you a higher voltage but at the same current rating. putting cells in parallel gives you the same voltage but at a higher current rating. series parallel can give you both..
What does high resistance mean?
High resistance refers to a material's ability to resist the flow of electric current. In electrical terms, it means that the material impedes the movement of electrons, resulting in lower current flow for a given voltage according to Ohm's Law (V = IR). High resistance is commonly found in insulating materials, which prevent electrical conduction and help protect circuits from unwanted current leakage.
Will series circuits decrease your electricity bill every month?
Series circuits themselves do not inherently decrease your electricity bill; rather, they affect how devices operate together. In a series circuit, the current is the same through all components, which can lead to reduced voltage for each device and potentially lower power consumption if devices are designed to work efficiently at lower voltages. However, the overall impact on your electricity bill will depend on the total power usage of the devices connected and their operating efficiency, rather than the circuit configuration alone.
How do you lower the current?
To lower the current in a circuit, you can increase the resistance using Ohm's Law (I = V/R), where I is the current, V is the voltage, and R is the resistance. Alternatively, you can reduce the voltage supplied to the circuit, which will also decrease the current. Additionally, adding resistors in series will increase the total resistance and thus lower the current flowing through the circuit.
What is advantage of a parallel circuit?
Parallel circuits have a higher current and a lower resistance.
How does the resistors work in a integrated circuit?
A resistor implements electrical resistance as a circuit element. It works in an integrated circuit by reducing current flow, and to lower voltage levels within circuits.
What is electricity that follows along the path?
Electricity that follows along a specific path is called a current. This flow of electric charge can occur in conductive materials like wires or circuits, moving from higher voltage to lower voltage. The amount of current is measured in amperes.
What difference in the bulbs causes this difference in the currents?
The difference in currents between the bulbs is primarily caused by variations in resistance. Bulbs with different wattages have different resistances, which affect how much current flows through them when connected to the same voltage source. Higher wattage bulbs typically have lower resistance, allowing more current to flow through them compared to lower wattage bulbs.
Why do solar cells need to lower resistance in the electrical circuits that make up their electronic system?
Reducing the resistance of solar cells increases the output current. Although the voltage remains the same the current is effected due to internal resistance. A reduction in output current can result in lesser diminished functioning in household appliances.
How does voltage in cells and batteries affect energy transfer in circuits?
Voltage in cells and batteries drives the flow of electric current in circuits. A higher voltage means more energy is available to push the electrons through the circuit, increasing the rate of energy transfer. Conversely, a lower voltage will result in slower energy transfer.
What is current trandformers?
I believe you meant transformer. If so it is a transformer used in high voltage circuits to reduce the current to a safer measurable value. It can be used as a direct input to a metering or protective relay to covert high currents to a lower value. It is used in AC circuits and typically encircles the conductor(s) it is monitoring, then works by using the expanding/ collapsing field which is the theory of induction used in transformer operation. It is the primary side of a "transformer" which only works when there is current flowing through it.
What is an over-current protective device?
That is called a fuse. A fuse is a protective device, which will interrupt the flow of electricity if it is subjected to a current that is greater than its rating. Some fuses are designed to handle a large inrush of current and are used in circuits such as air conditioners, where a large amount of current is needed at startup, for a short duration and then current drops to a lower level. These are sometimes called time-lag fuses.
Is there any way to lower your bonds in tamagotchi v5.5?
i think that if you want to lower your bonds all you have to do is ignore their training calls hope this helps
The electric bulb in your household circuits are connected in parallel what happens to the line current and line voltage as you turn on more light bulbs?
The line current increases when more bulbs are switched on in parallel, since more parallel current paths results in lower effective resistance. The line voltage should not change in response to any normal use of electric power in a single house.
What is the purpose of a small step down transformer in electrical circuits?
A small step-down transformer in electrical circuits is used to reduce the voltage from a higher level to a lower level. This helps to safely power devices that require lower voltage levels, protecting them from potential damage.
What is the difference between parallel and series circuits in terms of their electrical connections and how do they affect the overall performance of the circuit?
In a parallel circuit, the components are connected in separate branches, allowing current to flow through each component independently. This means that if one component fails, the others can still function. In a series circuit, the components are connected in a single path, so if one component fails, the entire circuit is disrupted. Parallel circuits have higher total current and lower total resistance compared to series circuits, which can affect the overall performance by providing more reliable and efficient operation.
