answersLogoWhite

0

Current sources are used as loads in differential amplifiers to improve their performance by providing high output impedance, which enhances the gain of the amplifier. They also help in maintaining a constant current through the differential pair, ensuring better linearity and increased common-mode rejection ratio (CMRR). This results in improved signal integrity and noise immunity, making differential amplifiers more effective for applications requiring precise signal amplification.

User Avatar

AnswerBot

2w ago

What else can I help you with?

Continue Learning about Engineering

What is active load?

When it is required to increase the gain of a differential amplifier for that we have to increase the collector resistance to a large value which is difficult and also require larger chip area ,so instead we replace it by a constant current source that is a current mirror which is called an active load.


What is the no load current of a 90kw motor operating 440V 60Hz?

The no-load current of a motor, such as a 90 kW motor operating at 440V and 60Hz, can vary based on its design and efficiency. Typically, the no-load current for such motors ranges from 10% to 30% of the full-load current. To estimate the no-load current, you can use the formula: No-load current ≈ Full load current × (no-load current percentage). The full-load current can be calculated using the formula: Full Load Current (A) = Power (W) / (Voltage (V) × √3 × Power Factor).


What is the percentage of the no-load current in a transformer to its full load current?

2 to 5% of full load current


The current load of a trnsformer is the current drawn by the?

Load!


What is the difference between no load current and no load voltage?

What does the question refer to? Induction motors? Transformers? For transformers, the no-load voltage is the voltage -- across the secondary or primary -- when there is no load attached to the secondary, that is, when there is no current in the secondary. No-load current really only makes sense when talking about a motor, because current is flowing in the device even when it's not under load. A rule of thumb is the no-load current is about a third to one half the full-load current.

Related Questions

What is an AF amplifier?

AF means audio frequency. Audio Amplifiers can be subgrouped as voltage amplifiers (or pre-amplifiers) and power amplifiers. The voltage amplifier will raise the level of level of the output of a microphone from say 1 mV to 500mV or 1V. The power amplifier will be the interface between this and the load, which is a speaker. The resistance of the speaker is often 4 ohm or 8 ohm. You cannot have a speaker with 1k as resistance! As such to get say 8W output, an amplifier providing 8V will have to pump 1 amp into an 8 ohm speaker. Thus power amplifiers will have to drive a lot of current into the load. Voltage amplifiers cannot do this. A power amplifier sometimes just has unity voltage gain, but has ability to drive a lot of current into the load. Typical power amplifiers are operated in class B, where for 50% of the signal swing, one transistor provides current, and for the other 50%, the other transistor in a class B provides current into load. Class B amplifiers have cross over distortion, But this can be overcome by pre-biasing, or making the stage operate as class AB. The power amplifiers can also be used to power low resistance loads such as a step up transformer.


What are different between sink current and souce current?

Perspective. They are one and the same, but from the perspective of a load and a generator, the load takes current (sinks it), and a generator generates it (sources it).


What is the corresponding statement for current sources?

The corresponding statement for current sources is that they provide a constant current to a circuit, regardless of the voltage across them. Unlike voltage sources that maintain a fixed voltage, current sources adjust their voltage output to ensure that the specified current flows through the connected load. In ideal conditions, a current source can deliver the same current even if the load resistance changes. However, real current sources have limitations and may not maintain the current under all conditions.


What is active load?

When it is required to increase the gain of a differential amplifier for that we have to increase the collector resistance to a large value which is difficult and also require larger chip area ,so instead we replace it by a constant current source that is a current mirror which is called an active load.


How does load current varies with the load resistance?

Load current is related to load resistance by an inverse relationship. The load current increases linearly as load resistance decreases. Remember, the less resistance, the more current.


What are ideal current and voltage sources?

Sources without internal resistances.ideal voltage source has 0 ohms in series with it, no internal voltage drop all voltage delivered to loadideal current source has infinite ohms in parallel with it, no internal current loss all current delivered to load


What is the no load current of a 90kw motor operating 440V 60Hz?

The no-load current of a motor, such as a 90 kW motor operating at 440V and 60Hz, can vary based on its design and efficiency. Typically, the no-load current for such motors ranges from 10% to 30% of the full-load current. To estimate the no-load current, you can use the formula: No-load current ≈ Full load current × (no-load current percentage). The full-load current can be calculated using the formula: Full Load Current (A) = Power (W) / (Voltage (V) × √3 × Power Factor).


What is the percentage of the no-load current in a transformer to its full load current?

2 to 5% of full load current


The current load of a trnsformer is the current drawn by the?

Load!


The current load of a transformer is the current drawn by the?

load


Why the waveform of no load current is not sinusoidal?

No load current is mostly inductive, hence the load current may not be a sine wave


What is the difference between no load current and no load voltage?

What does the question refer to? Induction motors? Transformers? For transformers, the no-load voltage is the voltage -- across the secondary or primary -- when there is no load attached to the secondary, that is, when there is no current in the secondary. No-load current really only makes sense when talking about a motor, because current is flowing in the device even when it's not under load. A rule of thumb is the no-load current is about a third to one half the full-load current.