To allow floor flange bolts to have a place to fit and to anchor the flange to the cement /wood decking
First, in order to accomplish this task, be sure the plastic flange fits the opening in question. It this is new work and anchor bolts or anchorbolt holes are not already in place, fit the flange to the lead drain line as you want it to go and by this guide, using a cement bit, drill holes in the cement(assuming the basement floor is cement). Two holes are required. After the holes are drilled, force lead inserts into the holes. These are to screw the anchoring bolts into to hold the flange stable. Choose the correct lead inserts and the side drill bit to match. Any hardware store can match these up for you. The remount the flange, through the proper holes in the flange, the ones you used as a guide for the holes, then insert the ancholr bolts and tighten down. It Holes are already in place and no lead inserts are already in the holes, simply obtain the proper inserts, bolts and Voila! do according to the above, simple yes?
With a tape measure.
The flange connects to the shower and just goes through the floor. It shouldn't mount to the floor.
No, it is not recommended to glue the toilet closet flange to the pipe. The flange should be secured to the floor using bolts or screws, and the toilet is then secured to the flange using wax rings or sealing gaskets. Gluing the flange to the pipe can make it difficult to remove or replace the toilet in the future.
To measure the ASA (American Standards Association) size of a pipe flange, you need to determine the nominal pipe size (NPS) and the flange's pressure class. Measure the outside diameter of the flange and the bolt circle diameter. Additionally, count the number of bolt holes and measure their diameter. These dimensions help identify the correct ASA flange standard for compatibility with piping systems.
To install a shower drain flange, first remove the old flange if necessary. Then, apply plumber's putty or silicone sealant around the underside of the new flange. Insert the flange into the drain opening and secure it in place with screws. Finally, connect the drain pipe to the flange and test for leaks.
To replace a shower drain flange, you will need to remove the old flange by unscrewing it from the drain pipe. Then, clean the area around the drain pipe and install the new flange by screwing it into place. Make sure to seal the flange properly to prevent leaks.
To properly install a toilet flange on tile, first ensure the tile surface is clean and level. Place the flange over the drain hole and mark the screw holes on the tile. Drill pilot holes for the screws, then secure the flange to the tile using screws. Make sure the flange is level and flush with the tile surface. Finally, connect the toilet to the flange using a wax ring for a secure seal.
To properly install a toilet flange on tile, first ensure the tile surface is clean and level. Place the flange over the drain hole and mark the screw holes on the tile. Drill pilot holes for the screws, then secure the flange to the tile using screws. Make sure the flange is level and flush with the tile surface. Finally, connect the toilet to the flange using a wax ring for a proper seal.
First, in order to accomplish this task, be sure the plastic flange fits the opening in question. It this is new work and anchor bolts or anchorbolt holes are not already in place, fit the flange to the lead drain line as you want it to go and by this guide, using a cement bit, drill holes in the cement(assuming the basement floor is cement). Two holes are required. After the holes are drilled, force lead inserts into the holes. These are to screw the anchoring bolts into to hold the flange stable. Choose the correct lead inserts and the side drill bit to match. Any hardware store can match these up for you. The remount the flange, through the proper holes in the flange, the ones you used as a guide for the holes, then insert the ancholr bolts and tighten down. It Holes are already in place and no lead inserts are already in the holes, simply obtain the proper inserts, bolts and Voila! do according to the above, simple yes?
To replace a tub drain flange, you will need to remove the old flange by unscrewing it from the drain pipe. Then, clean the area around the drain hole and apply plumber's putty to the new flange before screwing it into place. Finally, test the new flange to ensure it is securely installed and not leaking.
To replace a shower drain flange, you will need to remove the old flange by unscrewing it from the drain pipe. Then, clean the area around the drain pipe and install the new flange by screwing it in place. Make sure the new flange is securely attached before using the shower again.
Usually toilet flange is glued down onto plastic drain pipe. There is a toilet flange that can be glued inside of plastic drain pipe also.
I removed the broken flange by perforating the lead filling between the drain pipe and the flange - i.e., drilling holes every 1/4-1/2 inch or so with a regular drill and then sawing through the filling with a power saber saw. Then pried the flange off with a pry bar. Wasn't as bad as I expected. - Dan
Sink drains have holes on the sides to mate with the overflow drain above the drain flange. While most water goes down the top, some may overflow and go behind and though a channel in the wall of the sink. Then that water goes through one of the holes on the side of the drain and goes down. When you are installing it, you should try to align the holes with the overflow channel. You might have to compensate for rotation as you tighten the flange. In other words, you might want to partially block it to where any rotation will cause the pipe to rotate into the correct position. This can be inconvenient when you are attaching the drain kit to a sink that has no overflow holes. In that case, the holes in the pipe serve no purpose, and you have to make sure things are sealed well so it won't leak between the rubber flange and the holes on the side. There may also be a single, threaded hole further down. That is for the lever for the popup valve for the drain. The lever pushes the drain plug up and/or pulls it down.
To remove a shower drain flange, you will need to unscrew the screws holding it in place using a screwdriver or wrench. Once the screws are removed, you can lift the flange out of the drain. Be sure to clean the area before installing a new flange.
To remove a bathtub drain flange, you can use a drain key tool or pliers to unscrew it counterclockwise. Make sure to apply some lubricant to help loosen it if it's stuck. Once it's unscrewed, you can lift the flange out of the drain.