answersLogoWhite

0

I removed the broken flange by perforating the lead filling between the drain pipe and the flange - i.e., drilling holes every 1/4-1/2 inch or so with a regular drill and then sawing through the filling with a power saber saw. Then pried the flange off with a pry bar. Wasn't as bad as I expected. - Dan

User Avatar

Wiki User

10y ago

What else can I help you with?

Related Questions

How can I remove a shower drain flange?

To remove a shower drain flange, you will need to unscrew the screws holding it in place using a screwdriver or wrench. Once the screws are removed, you can lift the flange out of the drain. Be sure to clean the area before installing a new flange.


How do you remove the drain flange in a tub when the crosspiece is broken and there is no way to turn it and the water is leaking out of the drain into the basement?

get an "ID" (that is Inside Diameter) pipe wrench. they are available at most good hardware stores. this will allow you to turn the flange from the inside.


How can I remove a bathtub drain flange?

To remove a bathtub drain flange, you can use a drain key tool or pliers to unscrew it counterclockwise. Make sure to apply some lubricant to help loosen it if it's stuck. Once it's unscrewed, you can lift the flange out of the drain.


How can I replace a shower drain flange?

To replace a shower drain flange, you will need to remove the old flange by unscrewing it from the drain pipe. Then, clean the area around the drain pipe and install the new flange by screwing it into place. Make sure to seal the flange properly to prevent leaks.


How do I install a shower drain flange?

To install a shower drain flange, first remove the old flange if necessary. Then, apply plumber's putty or silicone sealant around the underside of the new flange. Insert the flange into the drain opening and secure it in place with screws. Finally, connect the drain pipe to the flange and test for leaks.


How can I replace a tub drain flange?

To replace a tub drain flange, you will need to remove the old flange by unscrewing it from the drain pipe. Then, clean the area around the drain hole and apply plumber's putty to the new flange before screwing it into place. Finally, test the new flange to ensure it is securely installed and not leaking.


How do I go about replacing a shower drain flange?

To replace a shower drain flange, you will need to remove the old flange by unscrewing it from the drain pipe. Then, clean the area around the drain pipe and install the new flange by screwing it in place. Make sure the new flange is securely attached before using the shower again.


How do you solder a closet flange to a lead drain pipe?

To solder a closet flange to a lead drain pipe, first clean the surfaces to be soldered with a wire brush. Apply flux to both the flange and the pipe, then use a propane torch to heat the joint. Once the lead and flange are hot enough, apply the solder to create a watertight seal.


How do you take a bathtub drain out?

To remove a bathtub drain, you typically need to unscrew the drain cover using a screwdriver or pliers. Then, use a drain removal tool to loosen and remove the drain flange. Finally, pull out the drain assembly from the bathtub.


How can I remove a tub drain?

To remove a tub drain, you can use a drain removal tool or pliers to unscrew the drain cover counterclockwise. Once the cover is removed, you can then use a wrench to loosen and remove the drain flange. Be sure to clean the area before installing a new drain.


How can I effectively remove a bath drain?

To effectively remove a bath drain, you can start by using a drain key or pliers to unscrew the drain cover. Then, use a drain removal tool to loosen and remove the drain flange. Finally, clean the area around the drain and replace it with a new one if needed.


How do you remove a PVC flange glued to a PVC drain pipe?

pvc flange if glued properly can not be detached you just need to cut it and fix up a new one if the old flange is useless. www.pvcpipe.in