0
In a Mazda RX-7, the motor may sometimes switch on one rotor due to the design of its Wankel rotary engine, which features two rotors that operate in a sequential manner. This can occur if one rotor is experiencing issues such as uneven wear, low compression, or fuel delivery problems, causing the engine management system to compensate by relying on the functioning rotor. Additionally, this behavior can be a result of the engine's design to optimize performance and efficiency under certain conditions. Regular maintenance and diagnostics are essential to ensure both rotors operate effectively.
What else can I help you with?
What is the part of an electric circuit generating force?
switch, motor or rotor.
How does the centrifugal switch work in a single phase electric motor?
In a single phase electric motor, the centrifugal switch allows the start winding to be energized through the start capacitor when the motor is starting. This gives an out of phase magnetic field that, along with the in phase magnetic field from the run winding, helps the rotor to begin spinning. Once the rotor reaches a certain speed, the centrifugal switch changes state and cuts off the start winding. At that point, the motor continues running only through its run winding, and inertia keeps the rotor properly phase biased relative to the run winding's magnetic field.
What type of rotor is found in a universal motor?
Wound rotor and squirrel-cage rotor
What type of motor has a stator?
An electric motor has a stator and a rotor. The stator does not move. The rotor rotates inside the stator.
What is the rotating coil in an electric motor called?
The part that rotates inside of an electric motor is called the rotor.
Will another Mazda engine work inplace of a rotor motor in a 1988 RX7?
no
What is the part of an electric circuit generating force?
switch, motor or rotor.
How does the centrifugal switch work in a single phase electric motor?
In a single phase electric motor, the centrifugal switch allows the start winding to be energized through the start capacitor when the motor is starting. This gives an out of phase magnetic field that, along with the in phase magnetic field from the run winding, helps the rotor to begin spinning. Once the rotor reaches a certain speed, the centrifugal switch changes state and cuts off the start winding. At that point, the motor continues running only through its run winding, and inertia keeps the rotor properly phase biased relative to the run winding's magnetic field.
What is difference of blocked rotor and locked rotor protection of motor?
What is difference of blocked rotor and locked rotor protection of motor?Read more:What_is_difference_of_blocked_rotor_and_locked_rotor_protection_of_motor
Why A synchronous motor is sometimes called a synchronous capacitor Explain?
A synchronous motor can operate as either a Generator or a Motor.When a synchronous motor has current applied to the windings on its rotor and the stator is energized with say a 50hz line supply (with little or no physical load) then the exact amount of excitation provided by the rotor can determine whether the stator displays inductive or capacitive properties.If the rotor is under excited (too Little rotor current) the Synchronous Motor will behave as an Inductor, however if the rotor is over excited then the Synchronous Motor will behave like a Capacitor.Hope this helps
What rotates on an electric motor?
The part that rotates inside of an electric motor is called the rotor.
What type of rotor is found in a universal motor?
Wound rotor and squirrel-cage rotor
What is locked rotor?
Locked rotor current is the amount of current a motor would draw if you energize the motor and the rotor (the spinning shaft) doesn't spin.
What type of motor has a stator?
An electric motor has a stator and a rotor. The stator does not move. The rotor rotates inside the stator.
In a dc motor the input power is given to stator or rotor?
rotor
What is the rotating coil in an electric motor called?
The part that rotates inside of an electric motor is called the rotor.
What is the minimum thickness for a Mazda 6 rear rotor?
8mm
