0
What else can I help you with?
How do you draw circuit diagram for digital clock using 74LS293 ic?
To draw a circuit diagram for a digital clock using the 74LS293 IC, start by using the 74LS293 as a decade counter for counting seconds. Connect the clock input to a timing source, such as a 1 Hz oscillator, to increment the count every second. Additionally, connect the outputs of the 74LS293 to a display driver such as a 7-segment display decoder (e.g., 74LS47) to visualize the time. Ensure to incorporate reset circuitry and any necessary components like resistors and capacitors for proper operation.
What is the Block diagram for time division multiplexing?
What is multiplexing and its diagram
What is total break time of circuit breaker?
refer to http://yourelectrichome.blogspot.com/2011/03/circuit-breaker-time-total-break-time.html
When is short circuit 3 coming out?
as far as i know there will not be a short circuit 3 coming out any time soon
Can you shut off one appliance at a time on a parallel circuit?
Only if you install separate switches for each part of the circuit. The whole point of a parallel circuit - is that both parts of the circuit are controlled by the same switch.
How do you draw circuit diagram for digital clock using 74LS293 ic?
To draw a circuit diagram for a digital clock using the 74LS293 IC, start by using the 74LS293 as a decade counter for counting seconds. Connect the clock input to a timing source, such as a 1 Hz oscillator, to increment the count every second. Additionally, connect the outputs of the 74LS293 to a display driver such as a 7-segment display decoder (e.g., 74LS47) to visualize the time. Ensure to incorporate reset circuitry and any necessary components like resistors and capacitors for proper operation.
Where can you learn to draw Naruto?
Im not really sure, but you can always learn how to draw ANIME and then draw him; but if you dont have that kind of time, then try to find a book on HOW TO DRAW NARUTO CHARACTERS, or tracing them. Or you can try this site for a tutorial: www.DeviantArt.com
Why dont your windows and wipers work gone down same time?
If on the same circuit, it may be the fuse.
Where you can get a wiring diagram for a 99 sunfire that shows the rear defrost circuit My brake lights turnhazards and rear defrost keep going out for short periods of time need diagram.?
In situations like this it is best to have a diagram to help. A diagram rear defrost wiring system of a 1999 Sunfire can be found in its maintenance manual.
Circuit diagram of sampling?
A circuit diagram of a sampling system typically consists of a signal source, a sampler (like a switch), a hold circuit (to retain the sampled value), and an analog-to-digital converter to convert the sampled signal into a digital format. The switch opens and closes based on a clock signal, allowing the signal to be sampled at discrete time intervals.
Block diagram of CRO?
block diagram of CRO means pictorial reprasantation of collaction of all parts of CRO ie.vertical amplifier, delay line,trigger circuit, time base genarator,horizontal amplifier ,electron gun&scree
Why does the fuse in 1997 Ford Expedition blow every time you replace it?
The fuse will blow when the current draw in the circuit that the fuse is protecting is more than the rating of the fuse. It usually indicates a faulty componet in the circuit or grounded wiring.
Im babysittin tomomrow and you dont knoiw what to do?
Well i bring things they can draw with and when its time to go to sleep i read them a book or sing to them
Why are symbols important in electronics?
To make things simpler! Imagine if they had to draw an actual transistor or battery everytime... that would have been both time consuming and difficult for the person studying the diagram ( as one engineer's drawing of a transistor may be totally different from others )
Why does Engine relay fuse blows as soon as you turn over the engine. thanks for the answer i dont have wire diagram but will do it the hard way .thanks.?
There is a dead short somewhere on the circuit. a fuse will only blow with a short. you need to get a wiring diagram of everything that is powered by that fuse and start checking for a broken wire, bad component, or a harness that has been chewed through by an animal or rubbed through from vibrating against something. This is may take some time to do. Good Luck!
How do you draw an electrical circuit diagram?
Visualize a ladder with the two main members on the side and rungs across from one side of the main members to the other side to the main member. The left member is usually the "hot" side and the right member of the ladder diagram is the neutral side. The devices are drawn in on the rungs of the ladder diagram. The end of the rung on the right is where the load of the rung is drawn in. Without a load in every rung there would be a short circuit when the power is applied to the circuitry. The European version of an circuit diagram has the ladder turned to the horizontal position. The "hot" rung is on the top and the neutral rung is on the bottom. These types of circuit diagram are called an electrical schematics but are sometimes refered to as ladder diagrams. Electrical schematics are an electricians road map. When troubleshooting electrical faults in control circuitry, upon opening the control panels door you are faced with a massive amount of wiring that seems to go everywhere. The schematic has a pictorial assessment of where each and every wire goes and what it is connected to. It allows you to trace circuit voltages without having to physically start at one end of the wire and see where it goes to. Reading the schematic you can read what the circuit is designed to do and where the voltage path should go if the system is working properly. A schematic is the main tool for troubleshooting electrical control circuitry. Without it troubleshooting can take up to four times the length of time it takes to find the fault.
What is Shunt reactor circuit diagram?
The fixed or mechanically switched reactors may be used for the absorption or generation of reactive power, the amount of reactive power produced is fixed and the response time is slow.
