0
What else can I help you with?
How do you replace a flapper in a toilet?
Shut the water supply off to the toilet. Flush the toilet. Pull the old flapper out and replace it with the same type. Turn the water back on and test the toilet.
How do you replace wax ring on toilet?
Shut off the supply line and disconnect it from the tank. Flush the toilet and hold the lever down until all the water runs out. If you are strong enough to pick up the toilet you can stop there, if not, use a sponge or towel and get the rest of the water out of the tank. Use a cup to get as much water out of the bowl as possible. On the base of the toilet on either side there should be two caps. Under these are the bolts holding the toilet down. Some toilets also have screws on either side at the front of the tank. If present, remove them also. If you can pick up the toilet, do so and set it on a towel. This will catch the water and also not scratch the floor. The old wax ring may be around the drain or on the bottom of the toilet. Remove it and the black ring that is probably there. If the drain is at least flush with the floor, a regular thickness ring should be enough. If there is any doubt, use an extra thick one or stack two together. The excess wax will push out. Put the new rings in place on the floor, make sure the bolts are pointing up and set the toilet back in place. Push down on the toilet at the back of the seat with all your weight to to compress the wax ring and form a good seal. Tighten the nuts and install the trim caps.If you can't pick the toilet up, tip it forward enough to get the ring under it and let it gently back down.If any of my employees used a sponge to remove toilet water Id fire them on the spot.In America we have something called a "wet dry Vacuum" a brand new invention that works wonders when removing water from a fixture or just for general cleaning .Using the wet dry will do the following1- Remove remaining water from a tank2- Remove water from the bowl3- Makes for easier dumpng rather then lifting china and the weight of waterAlso not all toilets are low down tanks some are flushometer and STILL a wet dry will work wonders
Where are shut-off valves?
In every home thee are a number of shut-off valves. Where the water pipe enters the house is the main shut off, usually beside the PRV, a bell shaped device for regulating the house pressure. This main cold line will then branch off to the water heater, bathrooms and kitchen. Each faucet and the water heater and the toilet will have a shut-off valve. The hot water line comes out of the top of the heater and goes to bathrooms and kitchen. Each hot faucet also has a shut-off valve under it.
How do you replace toilet flush valve?
Take tank off of the bowl and replace it . Always install new tank to bowl bolts and washers and tank to bowl gasket. The flush valve is what your tank ball is conected too. If your talking about ballcock then you just take it out with out having to do the above. The ballcock is what lets the water come into tank. Always shut off water either way. If you cannot get the bolts to come lose you will have to hack saw them off, it will take a little while to do so but it works best. You will only use the blade it self and turn the blade around. And you will be cutting between tank and bowl and put something on the bowl so not to scatch the bowl like duct tape or what ever you have like this. and if you have a brass nut on flush valve under tank you will have to cut it also
What is wrong whenWater is running on the floor but toliet is not leaking anywhere?
Your question isn't very clear. Toilet must be leaking somewhere. Shut off valve, supply line, the seal between the tank and the bowl or the wax ring underneath the toilet. In warm weather, the tank can sweat if the water filling it is cold in high humidity. It pretty much has to be one of these places.
What should you do when you flush the toilet and the water starts rising?
If the water starts rising after you flush the toilet, you should quickly turn off the water supply to the toilet by twisting the shut-off valve located behind the toilet. This will prevent the toilet from overflowing.
How do you replace a flapper in a toilet?
Shut the water supply off to the toilet. Flush the toilet. Pull the old flapper out and replace it with the same type. Turn the water back on and test the toilet.
What are the benefits of a slow close toilet seat hinge and how does it enhance the overall experience of using a toilet seat?
A slow close toilet seat hinge prevents the seat from slamming shut, reducing noise and potential damage. It also enhances safety by preventing fingers from getting pinched. Overall, it provides a more comfortable and convenient experience when using the toilet seat.
What is the best way to replace a 4 inch toilet flapper in a toilet?
To replace a 4-inch toilet flapper in a toilet, first shut off the water supply to the toilet. Remove the old flapper by disconnecting it from the flush valve. Install the new flapper by attaching it to the flush valve and ensuring a secure fit. Turn the water supply back on and test the toilet to ensure the flapper is working properly.
Is it bad to shut off the water to the toilet?
Shutting off the water to the toilet is not necessarily bad, but it can prevent the toilet from flushing properly. It is important to only shut off the water when necessary for repairs or maintenance.
How do you empty a toilet tank?
To empty a toilet tank, locate the shut-off valve near the base of the toilet and turn it clockwise to stop the water flow. Then, flush the toilet to remove most of the water from the tank. Use a sponge or towel to soak up any remaining water in the tank.
If your cats love to dunk their head in the toilet how do you get them to stop?
Close the toilet seat or toilet door, also, close the door of the bathroom if you don't want to keep the bathroom door shut for some reason just put something in front of the door to block it. Your cat is probably thirsty. Put the toilet seat down, and change its water in its bowl regularly.
Why won't the toilet valve shut off?
The toilet valve may not shut off due to a faulty valve, a blockage in the water line, or a problem with the float mechanism. It is important to check these components and make necessary repairs to ensure proper functioning of the toilet.
How do you shut off the water to a toilet?
To shut off the water to a toilet, locate the shut-off valve usually located behind or near the toilet. Turn the valve clockwise to close it and stop the water flow to the toilet.
Just installed a new flapper on my toilet and turned off the water to do so at the toilet then on again but the water shutoff pops out after every flush and it won't refill Help?
It depends what you mean by shut off POPPING OUT? More info needed
Is your toilet shut off valve leaking and in need of repair?
Is your toilet shut off valve leaking and needs fixing?
What is the purpose of a toilet shut off valve and how can it be used to prevent water damage in case of a plumbing emergency?
The purpose of a toilet shut off valve is to control the flow of water to the toilet. In case of a plumbing emergency, such as a leak or overflow, the shut off valve can be used to quickly stop the flow of water to prevent further damage. It is important to know the location of the shut off valve and how to use it in case of an emergency.
