answersLogoWhite

0

Because it has to deal with a higher current. Since the secondary power rating is practically equal to the primary power rating, the lower voltage winding must handle a larger current than the higher voltage winding. So the lower voltage winding must use a heavier conductor.

However, the question should ask "Why does the low-voltage winding of a transformer use thicker wire?"

Remember, the terms 'primary' and 'secondary' have nothing to do with voltage! The primary winding is the winding connected to the supply, whereas the secondary winding is the winding connected to the load!

So, for a 'step down' transformer, the secondary voltage is lower while, for a 'step-up' transformer, the secondary voltage is higher.

User Avatar

Wiki User

∙ 9y ago
User Avatar

What else can I help you with?

Continue Learning about Engineering

Can you replace DY11 by DYN11 transformer?

Yes, you can replace a DY11 transformer with a DYN11 transformer, but it is important to consider the differences in their winding configurations and phase shifts. The DY11 transformer has a wye (star) connection on the primary side and a delta connection on the secondary side, while the DYN11 transformer has a delta connection on the primary side and a wye connection on the secondary. This change in configuration may affect voltage levels and phase relationships in your system, so it's essential to ensure compatibility with existing equipment and load requirements. Always consult with an electrical engineer before making such a replacement.


Why is star connection used in a three phase transformer?

A star-delta connection is used in transformer connection for below described reasons: 1. During transmission, the Star connection of Transformer is kept at Transmission side as Phase voltage in star connection is equal to 1/√3 times of line voltage and hence the insulation required is very less as compared if delta is kept at transmission side. By this connection there will be a phase shift of 30deg in the primary and secondary voltages. So this connection saves a lot of money on insulation and in this connection the neutral of Star connection is grounded as a result earth plays a role of reference for checking balancing of phase. 2. During Distribution, at Sub-station side Star-Star connected transformer is used and at lower distribution Delta-Star connection is used to compensate the phase shift and also to have a three phase four wire system at distribution end.


What is the use of a transformer with turns ratio 1?

isolation if you are in the usa and must service electronics the neutral is grounded the power supply is a voltage doubler one side is 170v+ to ground the other is 170v negative to ground so if you run the power thru the transformer first you stand a better chance of staying alive these transformers are quite often used to trigger scrs or triacs for the same reason


If a dc voltage of 12v is added to the secondary of step down transformer and rating of transformer is 220 input and 12v output what will be the result from primary of transformer?

Adding a DC voltage to the secondary of a transformer will not have an effect on the primary side, as transformers work on the principle of electromagnetic induction which is based on alternating current. The primary side of the transformer will still operate based on the input AC voltage of 220V. The DC voltage on the secondary side will not be transferred to the primary side.


Does the fuse on the primary side of a transformer protect the secondary side?

Yes, but it's usual to have fuses on both sides of the transformer.

Related Questions

Why neutral is ground in the circuit?

In the transformer at the secondry side one end of the winding will make star connection means 0 point there will be no voltage at that end if any leake voltage appear at that point it have to ground that what all the neutral points to be grounded


How many bushing do you get on delta to star transformer?

Your use of the word "bushings" implies you are dealing with a high-voltage transformer (over 600 volt). A three phase STEP-DOWN transformer normally has 3 bushings on the Primary side regardless of whether it is star-delta or another type. The Secondary side might have 3 or 4. A single phase transformer normally has 2 bushings on the Primary side and 2 or 3 on the Secondary side. If the transformer is being used to STEP-UP, it would be reversed from above. If this does not answer your question, I need more info.


How do you Ground a 3 wire service?

If you do not have a underground metal water pipe coming into the building then you put a ground rod at least 2 feet from the buildingf into the ground attach one end of the wire to ground rod run your ground wire and attach the other end to the neautral bar in the panel box. You need special transformer called as grounding transformer for this purpose. Grounding transformer is basically Wye-Delta type transformer with Wye connected winding connected to 3 line wires and derived neutral from Wye side grounded through desired grounding device. Delta side winding of grounding transformer is kept at no load.


Why is the neutral point grounded on a transformer?

The secondary side (output) of a three phase transformer develops a "separately derived system". That is why you do notsupply a neutral to a three phase transformer. It develops its own reference to ground by being bonded to the transformer casing and to a substantial earth ground, such as a ground rod. The XO tap on a transformer provides the neutral to the secondary line. It will have a double wire lug. The neutral wire going to the panel being supplied goes under one lug and the same size wire is to go to the ground lug on the transformer chassis The ground lug is also a double with the other lug to be wired to the earth ground.


Where is the use of earth transformer?

It is used in where the transformer are connected in star delta.


Star-star connection of transformer?

Star Star TransformerStar Star Transformer is formed in a 3 phase transformer by connecting one terminal of each phase of individual side, together. The common terminal is indicated by suffix 1 in the figure below. If terminal with suffix 1 in both primary and secondary are used as common terminal, voltages of primary and secondary are in same phase. That is why this connection is called zero degree connection or 0o - connection.If the terminals with suffix 1 is connected together in HV side as common point and the terminals with suffix 2 in LV side are connected together as common point, the voltages in primary and secondary will be in opposite phase. Hence, Star Star Transformer connection is called 180o - Connection, of three phase transformer.Vikram Meena


How transformer conduct current through ground?

A transformer doesn't 'conduct current through the ground'. However, in the event of a ground fault in the circuit supplied by a grounded transformer, the resulting fault current will flow through the earth back to the grounded terminal of that transformer's secondary winding.


How tertiary winding of power transformer acts as stabilizing winding?

in star-star neutral transformer at unbalanced load condition zerosequnce current will be flows in secondary side but this current can not be balanced by primary side because its not having neutral to circulate zerosequence current.due to this unbalance voltage will appeared in primary side but the tertiary delta winding allows circulate the zerosequence current so the primary voltage will get stabilized.


Why you uluminium on primary side of transformer?

This isn't the case. You can have aluminium or copper on primary or secondary side of a transformer.


What the purpose of the H1 terminal on a transformer?

The terminals H1 and H2 an a transformer indicate the primary side of the transformer. The secondary side is usually identified as X1 and X2.


What is a tap changing transformer?

A transformer that has part of one winding partitioned in such a way that it can be removed or added to the winding. For example, you may have a transformer with 100 turns on the low side and 1000 turns on the high side. If it were a tap changing transformer on the high side winding, you may be able to add or subtract 100 turns, so the turns ratio can be anywhere from 9/1 to 10/1. <<>> This type of transformer is in common use in home distribution systems. On the side of the transformer there is a handle with the markings of 14,400/7200. By having this ability to work on two different primary voltages the utility only has to stock one transformer. The same transformer can be connected to the grid across phases at 14,400 or phase leg to ground at 7200 volts. The transformer ratios are so wound that the output voltage remains at 120/240.


What is transformer tap changing?

A transformer that has part of one winding partitioned in such a way that it can be removed or added to the winding. For example, you may have a transformer with 100 turns on the low side and 1000 turns on the high side. If it were a tap changing transformer on the high side winding, you may be able to add or subtract 100 turns, so the turns ratio can be anywhere from 9/1 to 10/1. <<>> This type of transformer is in common use in home distribution systems. On the side of the transformer there is a handle with the markings of 14,400/7200. By having this ability to work on two different primary voltages the utility only has to stock one transformer. The same transformer can be connected to the grid across phases at 14,400 or phase leg to ground at 7200 volts. The transformer ratios are so wound that the output voltage remains at 120/240.