answersLogoWhite

0

Transformers without regulators in them will output voltage depending on the voltage coming in.

For instance if you have a 230v to 110v transformer then you will have a ratio of 23:11

this means for every 23 turns in the transformers primary side you will get 11 turns on the secondary, so if you have an input voltage of 247v then the output voltage will be around 118v, conversly if you have an inout voltage of 221v then the ouplut voltage will be around 106v.

User Avatar

Wiki User

13y ago

What else can I help you with?

Continue Learning about Engineering

Can a high voltage transformer be megged with a megger meter?

No. A megger's output voltage is not high enough to test the insulation of a high-voltage transformer if, by 'high-voltage transformer ', you mean a distribution transformer or power transformer. Instead, a high-voltage test set or 'pressure tester' (e.g. a 'HiPot' tester) must be used, as these produce far higher voltages.


Why instruments are connected on low voltage side of the transformer while performing no load test?

since we need to get desired or rated voltage, so if it is connected in high voltage side of the transformer, voltage supply will be more, and hence the current will be more than the required amount. this is the reason why the instruments re connected at the low voltage of the transformer while performing no load test.


Where is the high side of transformer on open circuit test?

high voltage side call primary


How to test Excitation Current of a transformer?

To test the excitation current of a transformer, you can perform an open-circuit test, where the primary winding is connected to the rated voltage while the secondary winding is left open. Measure the current flowing through the primary winding using an ammeter; this current is the excitation current. It's essential to ensure the transformer is at the specified voltage and frequency during the test for accurate results. Additionally, record the voltage and power factor for further analysis if needed.


What will happen to the transformer if double the rated voltage is applied to the winding during the open circuit test?

no voltage will be induced on the secondary side of the motor as the windings will become saturated.

Related Questions

How can I test a doorbell transformer to ensure it is functioning properly?

To test a doorbell transformer, use a multimeter to measure the voltage output. Disconnect the transformer from the power source and test the voltage across the terminals. A properly functioning transformer should have a voltage output within the specified range.


How do you calculate transformer voltage ratio test?

Secondary voltage / primary voltage


Can a high voltage transformer be megged with a megger meter?

No. A megger's output voltage is not high enough to test the insulation of a high-voltage transformer if, by 'high-voltage transformer ', you mean a distribution transformer or power transformer. Instead, a high-voltage test set or 'pressure tester' (e.g. a 'HiPot' tester) must be used, as these produce far higher voltages.


How can I test a transformer on a furnace?

To test a transformer on a furnace, you can use a multimeter to check the voltage output. First, turn off the power to the furnace. Then, locate the transformer and measure the voltage across the primary and secondary terminals. If the voltage matches the specifications provided by the manufacturer, the transformer is functioning properly. If not, the transformer may need to be replaced.


Why instruments are connected on low voltage side of the transformer while performing no load test?

since we need to get desired or rated voltage, so if it is connected in high voltage side of the transformer, voltage supply will be more, and hence the current will be more than the required amount. this is the reason why the instruments re connected at the low voltage of the transformer while performing no load test.


What is power frequency withstand voltage test?

A test done on a transformer. The voltage at the power frequency is ramped up to verify the transformer is capable of handling the stresses due to switching and natural phenomena (lighting strikes).Withstand Voltage:The voltage which has to be applied to a test object under specified conditions in a "withstand test" is called the "withstand voltage".


What are the purposes of performing no load test for the transformer?

These two tests are performed on a transformer to determine (i) equivalent circuit of transformer(ii)voltage regulation of transformer(iii) efficiency of transformer. The power required for theseOpen Circuit test and Short Circuit test on transformeris equal to the power loss occurring in the transformer.


What are the steps for testing a doorbell transformer to ensure it is functioning properly?

To test a doorbell transformer, follow these steps: Turn off power to the transformer at the circuit breaker. Use a multimeter to check the voltage output of the transformer. Connect the multimeter leads to the transformer's output terminals. Turn the power back on and check the voltage reading on the multimeter. The voltage should match the transformer's rated output voltage. If the voltage is significantly lower or higher, the transformer may be faulty and need to be replaced.


Why open circuit test is done on the transformer with low voltage side shorted?

The supply is given on the high voltage side of transformer because the supply voltage required to circulate rated current through the transformer is usually very small So energy is saved.


Why is a high dc voltage applied to a transformer for testing?

A high dc voltage would be applied to test the insulation between the windings.


Why were instrument of a transformer placed on a high voltage side in short circuit test?

I assume "tension" in this question should be replaced with "voltage". Short circuit tests are often performed from the lower voltage side of the transformer, since a lower voltage source is then required to perform the test. Often times the test lab may not have a source that can output a high enough voltage to perform from the high voltage winding.


Where is the high side of transformer on open circuit test?

high voltage side call primary