0
Why would the circuit breaker short when a multilight lamp on the end of a run with a pull chain switch is turned on?
The cicuit braker should only trip when there is too much current running through it. Check to see what the braker is rated for (maybe 10 or 15 amps). Then take stock of what equipment is in that circuit (maybe a couple of lights?) and estimate how many amps the circuit should be drawing (maybe two or three). If there aren't a million lights plugged in to this circuit then chances are the light fixture in question is shorting out when you turn it on.
What else can I help you with?
Can a Circuit breaker be used as a Switch?
Yes a circuit breaker is a switch but it should not be used as a switch. The continuous turning off and on of a breaker weakens the internal mechanism and reduces the tripping value of the breaker. There is in the marketplace breakers that are designed to be used as switches. These are usually used in large warehouses where the lights are turned on in the morning and shut off at night. Using these specifically designed breakers for switches does not wear out the tripping mechanism or reduce the tripping value. <<>> A circuit breaker can be used as a switch, although in most cases there are less expensive switches you can use.
What opens or closes an electrical circuit?
That function was traditionally implemented in the form of a mechanical deviceknown as a "switch".The practice became so firmly embedded in the art and science of electricitythat the word became the generic term for any device that could performany similar function, so that now we have "switching transistors", integrated"CMOS switches", and even central office telephone-circuit "switches".
How do you make a circuit so the lights can be turned on and off separatley?
To design a circuit so that lights can be turned on and off separately, we connect the circuit in parallel.
Compare and contrast a circuit breaker and a fuse?
A circuit breaker is something you can reset. When the switch "trips", the position of the switch goes to the middle. To reset it, move to Off, then On.When a fuse blows, its two external contacts are no longer connected by the internal piece of fuse wire and an electrical current can no longer flow.More technical details about fusesIn all types of disposable fuse, two contacts which are on the body of the fuse are connected to a piece of fuse wire inside. The material used to make the fuse wire, and its thickness, designed to melt - and thus break the circuit - if the current flowing through it exceeds a certain amperage, which is known as the fuse's "maximum rated current".There are many different types of disposable fuse: some are screwed into what looks like a light bulb socket.Other types are small tubes - made of glass or ceramic - with a metal contact at each end. They are held in a fuse holder that has contacts, clips or springs which make contact with each of the fuse's end contacts.Some commonly used automotive fuses are made of plastic and have two flat metal "pins" which plug into a pair of contacts in the fuse box.
Are switches wired in parallel?
Yes, switches in a circuit are typically wired in parallel. This allows each switch to control the same load independently; when one switch is turned on, it completes the circuit and allows current to flow, regardless of the position of the other switches. This configuration is commonly used in lighting circuits, enabling multiple switches to operate the same light fixture from different locations.
Why does the breaker trip when the switch is turned off?
When the switch is turned off, the breaker trips to protect the electrical circuit from overload or short circuit. This happens because the sudden interruption of the electrical flow can cause a surge of electricity, triggering the breaker to trip and cut off the power to prevent damage to the circuit.
What could be the problem if a breaker trips when the light is turned off?
If a breaker trips when the light is turned off, it could indicate a short circuit or an overloaded circuit in the wiring. It could also be due to a faulty breaker or an issue with the light fixture itself. It is recommended to consult a licensed electrician to investigate and resolve the issue safely.
How do you de-energize a circuit?
To de-energize a circuit, the voltage has to be cut off at the source. This is usually done with a disconnect switch which is located just before the circuit's load. Turning off the breaker on a distribution panel will de-energize the circuit it is feeding. To make sure that the voltage can not be turned back on when work is being done on the circuit, the switch or breaker must have a lock off device to prevent the circuit from being turned on, except by the person that locked the circuit off.
Could a bad circuit breaker light switch or plug outlet cause the bedroom light to flicker when turned on?
Yes a bad circuit breaker and a bad light switch can cause a light to flicker when its turned on. It could also be caused by loose wiring going or coming from that paticular circuit. it also could be something in the fixture itself causing. Checking for loose connections is your cheapest and first route to go.
Why did electricity along the line go out when switch was turned on?
There could be several reasons for the electricity to go out when the switch is turned on, such as a blown fuse, overloaded circuit, short circuit, or a faulty switch. It's important to investigate the cause further to determine the exact issue and address it appropriately to restore power.
Why does the circuit breaker immediately trip when the power is turned on?
The circuit breaker immediately trips when the power is turned on to protect the electrical system from overloading or short circuits, which can cause damage or fires.
Can you get electrocuted if the switch is off but the breaker is on?
Yes you can. The proper wiring of a switch is to bring the hot wire to the top of the switch terminal and connect the load to the bottom of the switch. When the breaker is turned off it disconnects the voltage from the top of the switch and the switch is then safe to work on. By not turning the breaker off, the voltage is present at the top of the switch which could subject you to a nasty shock if you come into contact with it.
What device can break an electric circuit?
There are 2 different types of these devices: circuit breakers (which can be reset after the problem is fixed) and fuses (which must be replaced after the problem is fixed).
What happened when you turned on the switch of the light?
A switch is placed in an electrical circuit in order to place a gap when the switch is off, so the circuit is broken. When the switch is on, the circuit is complete and the electricity can flow round the circuit.
What is the difference if a switch is before or after a bulb in a circuit?
It is a safety concern. With the switch before the bulb, the bulb is completely isolated from the potential source when the switch is turned off. With the switch behind the bulb, even if the switch is turned off, the potential source is still at the bulb. If any of these lamp holder parts touch the ground when removing the bulb the circuit will short out and trip the breaker. If you are grounded and touch any of the lamp holder parts you will get a nasty shock.
A circuit with a switch turned to the Off position or a circuit with any break is called?
a closed circuit
Can a Circuit breaker be used as a Switch?
Yes a circuit breaker is a switch but it should not be used as a switch. The continuous turning off and on of a breaker weakens the internal mechanism and reduces the tripping value of the breaker. There is in the marketplace breakers that are designed to be used as switches. These are usually used in large warehouses where the lights are turned on in the morning and shut off at night. Using these specifically designed breakers for switches does not wear out the tripping mechanism or reduce the tripping value. <<>> A circuit breaker can be used as a switch, although in most cases there are less expensive switches you can use.
