0
What else can I help you with?
What is the function of foot valve in the pump?
A foot valve, in relation to a water well, is a check valve at he bottom of a well to keep the water from running back into the well from the pump when the pump is not running. If the check valve does not hold the water the pump will lose it's prime and will not pump water.
What is the function of back pressure valve in Boiler feed pump?
The function of back pressure valve is to prevent back flow to the pump in case there is an obstruction on downstream side of valve.
How does the valve reservoir and pump function on a hydraulic cylinder jack?
the pump supply's the pressure, the resivoir supply's the fluid, the valve dirercts the fluid into the cylinder, to extend or retract the cylinder.
Boiler works but no hot water?
Sounds like you have a bad zone valve or zone pump. There is either a pump, and the zones in the house have zone valves, or each zone has it own pump. Zone valves go bad all the time, you can just replace the motor on it instead of sweating the new valve in. The box that is on top of the valve.
What is theFunction of arc valve in boiler feed pumps?
The ARC valve provides protection for centrifugal pumps during low flow conditions. It recirculates a minimum flow requirement automatically to the deaerator to prevent the pump from overheating and causing internal damage. Pump manufacturers will dictate a pump's minimum flow requirement. The ARC valve will be designed to flow normal capacities through the main valve and also size the bypass to handle the minimum flow. Additionally, the flow sensing element, a disc, also acts as a check valve to prevent reverse flow to the pump.
What valve do you close on a pump down?
section valve to be close before Type your answer here...
What is a star delta starter if a pump is connected to the motor should the outlet valve close before starting?
yes should to close few second due to air.
How do you pump up a bike tire with a skinny valve?
To pump up a bike tire with a skinny valve, you will need a pump that is compatible with a Presta valve. First, unscrew the small nut on the valve to open it. Then, attach the pump nozzle securely to the valve and pump air into the tire until it reaches the recommended pressure level. Finally, screw the nut back onto the valve to close it.
How do you inflate a tire with a presta valve?
To inflate a tire with a presta valve, follow these steps: Unscrew the small nut on the top of the valve to open it. Attach the pump nozzle securely to the valve. Pump air into the tire until it reaches the desired pressure. Remove the pump nozzle and tighten the nut on the valve to close it.
Can you put a check valve in line to a water pump if the foot valve is leaking?
It will only work properly if you put it very close to the foot valve. In which case you may as well replace the foot valve - it's not difficult to do. If you put it at or near the pump, the pump will just suck air.
What is the best way to properly use an air pump for a bike?
To properly use an air pump for a bike, first ensure the pump is compatible with your bike's valve. Attach the pump securely to the valve, then pump air into the tire until it reaches the recommended pressure level. Check the pressure with a gauge if needed. Disconnect the pump and close the valve.
In sump pump discharge line check valve is installed before or after gate valve?
after gate valve, because when you want make maintenance for sump pump , you don't want all water in the pipe drop down sump pump - gate valve - non return valve
How can you pump a Presta valve without using an adapter?
To pump a Presta valve without using an adapter, you can unscrew the top nut of the valve to open it, then use a pump with a nozzle that fits directly onto the valve. Make sure the pump is compatible with Presta valves before attempting to inflate.
How do you properly fill a presta valve with air?
To properly fill a presta valve with air, first unscrew the top nut to open the valve. Then, attach the pump nozzle securely onto the valve. Pump air into the tire until it reaches the desired pressure. Finally, remove the pump nozzle and tighten the top nut to close the valve.
How do you properly air a Presta valve?
To properly air a Presta valve, first unscrew the top nut to open the valve. Attach the pump nozzle securely to the valve. Pump air into the tire until it reaches the desired pressure. Close the valve by screwing the top nut back on.
What location must a check valve be placed?
Generally, placed close to the supply discharge of the pump.
How do you properly use a pump to inflate a bike tire?
To properly use a pump to inflate a bike tire, first ensure the pump nozzle is compatible with the valve on the tire. Attach the nozzle securely to the valve, then pump air into the tire until it reaches the recommended pressure level. Disconnect the pump and close the valve. Check the tire pressure with a gauge and adjust if necessary.
