answersLogoWhite

0

If the oil leak in your 1998 Volvo Turbo S70 is specifically from the turbo oil return lines, you may not need to replace the entire turbo. In many cases, you can buy a gasket or seal kit specifically for the return lines, which can effectively resolve the leak. However, it's important to inspect the turbo for any other signs of wear or damage, as that could warrant a replacement. Always ensure you address any leaks promptly to prevent further engine damage.

User Avatar

AnswerBot

3mo ago

What else can I help you with?

Related Questions

How do replace gasket on oil cooler 93 Chevy 1500?

First you must unscrew the oil filter and remove the 2 lines going into the adaptor. Unbolt the 2 bolts holding the adaptor to the motor. Remove the adaptor. Clean gasket from adaptor and block. Replace gasket and resemble the way you took it apart. You can take the oil filter off then take the 2 bolts out of the adapter plate this will allow the adapter to be pulled down enough to replace the gasket witch is an oring. If you take the lines off they are quick release.


Why would the transmission not stop leaking fluid?

The pan gasket could be leaking ( tighten mounting bolts or replace gasket ) Filler pipe rubber seal , Transmission oil lines ( tighten , replace ) Speedometer connector ( replace o-ring ) Some makes have a transmission vent pipe ( transmission over filled ) Output shaft seal damaged (replace)


How do you change a head gasket on a 2001 Chevy Cavalier?

Take the intake as well as all hoses and lines off of the top of the engine. Remove the valve cover gasket. Unbolt the exhaust manifold. Unbolt the head and remove. Replace the gasket, then reverse the procedure to finish the installation.


What do you need to do your 1997 dodge neon transmission keeps slipping and leaking fluid?

You did not mention where the leak is coming from. If it is from around the pan gasket, tighten the pan bolts. If from the cooler lines, tighten the hose clamps or replace the lines. In either case, add fluid to the proper level - or change the fluid, filter and gasket.


How do you replace the gaskets on intake manifold for 2002 suburban?

To replace the Suburban manifold gaskets, unhook everything on the manifold, from fuel lines to vacuum hoses. The manifold needs to be unbolted then removed. Clean the old gasket material, then install with a new gasket. Make sure to use factory specs when torqueing down the bolts.


Fuel pump replacement instructions and type on 1983 Oldsmobile cutlass?

Mechanical engine mount? Remove old one Install new making sure cam is under lever to activate replace mounting gasket and fuel lines Mechanical engine mount? Remove old one Install new making sure cam is under lever to activate replace mounting gasket and fuel lines


How do you replace the throttle body mounting gasket on a 93 Chevy 350 engine?

Disconnect negative cable from battery, relieve fuel pressure, disconnect throttle cable, disconnect fuel lines, disconnect any vacuum lines, disconnect electrical plugs, remove bolts holding throttle body, lift off throttle body, remove damaged gasket, clean area, replace in reverse order.


How many lines should be return ADDRESS?

a return address should have 2 lines


How do you replace fuel return valvs on 85 85 Jaguar XJ6?

To replace the fuel return valves on an 1985 Jaguar XJ6, first ensure the vehicle is off and the fuel system is depressurized. Remove any necessary covers to access the fuel rail, then disconnect the fuel lines from the return valves. Unscrew and replace the old valves with new ones, ensuring they are properly seated and sealed. Reconnect the fuel lines, check for leaks, and start the engine to ensure proper operation.


How do you replace a fuel pump on a 1969 Ford Mustang 302?

Remove fuel lines Remove 2 mounting bolts Slide fuel pump out Replace pump and gasket Make sure engine cam operates fuel pump lever


Do you remove tires to replace brake lines?

You remove the wheels to replace brake lines.


Need a diagram of the ac lines for a 2001 Volvo s60?

yes