The answer from GKK below was very helpful. There is one small difference between his 2003 Saab 9-3 and my 2001 Saab 9-5 Aero. There is a metal clip holding the bulb socket in place. I took the clip off from the top and then unplugged the old low beam headlight bulb. I used some dielectric grease (available at Advanced Auto for $1) to coat the prongs of the new headlight bulb. Other than those small changes between the 9-3 and the 9-5, everything stated below works fine.
Also, make sure you ask for your military discount at Advanced Auto or Auto Zone. Both are real good to honor your service with a 10% discount. I appreciate them for being the few that still do that especially when the USA is presently deployed in two wars.
I hope this answers the question for you. I have a 2003 SAAB 9-3 and I'm hoping it's the same as for a 9-5. I just replaced the low-beam bulb on the passenger side. Bought at Autozone for $14.99 (H7 Sylvania Halogen). 1. Remove rubber cover. 2. Pull and twist plug to the right (towards drivers side). It should slip right off when everything is aligned. Use a flashlight. 3. Now that you have the plug assembly out, pull out the bulb. Easier said then done. It's in there very tight. I actually used a needle nose plier to grap a hold of the bulb plate itself. This doesn't twist, nor is it clipped on. It's just in there tight. So use the plier, and work you way around the bulb plate (don't know what else to call it). Tah, dah... I believe there's only one way for the new bulb to go in, so insert it into the plug and put everything back. Hope this works for your 9-5. Good luck from GKK.
“how to replace headlight bulb 2003 park ave”
How do you replace a front indicator bulb in a Saab 93
To replace a headlight on a 2001 Saab 9-5 wagon, first, open the hood and locate the headlight assembly. Remove the plastic cover or housing by unscrewing any retaining screws or clips. Disconnect the electrical connector from the old bulb, then twist the bulb socket counterclockwise to remove the old bulb. Insert the new bulb, reconnect the electrical connector, and reassemble the headlight housing.
take it to the dealer and let them do it
autozone.com repair info
Take a hammer. smash the headlight assy. lens. Remove old bulb, put in new.
To replace a left dipped bulb on a Saab 9-3, first, open the hood and locate the headlight assembly. Remove the cover or access panel on the back of the headlight, then disconnect the electrical connector from the bulb. Twist the bulb socket counterclockwise to remove it, replace the old bulb with a new one (ensuring not to touch the glass), and reassemble the socket and connector before closing the hood. Make sure to test the new bulb to ensure it’s functioning properly.
To replace a headlight on a 2003 Infiniti Q45, first, open the hood and locate the headlight assembly. Remove the retaining clips or screws securing the assembly, then gently pull the assembly out. Disconnect the wiring harness from the back of the headlight bulb, replace the old bulb with a new one, and reassemble everything by reversing the steps. Ensure the new bulb is securely connected before testing the headlight.
Replace headlight bulb only when blown.
On older vehicles you replace the entire headlight. On the newer vehicles you just replace the bulb unless the headlight assembly is damaged.
I need to replace the bulb on the driver side of my 2003 Dodge Grand Caravan. After searching this forum I found a similar question regarding the 2000 Caravan. It talked about under the hood removing three screws and pulling out the headlight assembly. I tried this and it worked on the 2003. 1) open the hood. 2) Carefully remove the three screws holding the headlight assembly in place. In my case the screws were black. Be careful as they are screwed into plastic. 3) Carefully slide the headlight assembly out. At this point you can replace the headlight bulb, turn signal bulb, or the entire headlight assembly. To replace the headlight bulb turn the collar holding the bulb in counter clockwise. Pull the bulb out of the headlight assembly. Replace the bulb. Insert the bulb into the headlight assembly insert the collar and turn clockwise until it locks. 4) Carefully insert the headlight assembly back into place. 5) Replace the three screws removed in step 2 being carefull not to over tighten.
1) open the hood. 2) Carefully remove the three screws holding the headlight assembly in place. In my case the screws were black. Be careful as they are screwed into plastic. 3) Carefully slide the headlight assembly out. At this point you can replace the headlight bulb, turn signal bulb, or the entire headlight assembly. To replace the headlight bulb turn the collar holding the bulb in counter clockwise. Pull the bulb out of the headlight assembly. Replace the bulb. Insert the bulb into the headlight assembly insert the collar and turn clockwise until it locks. 4) Carefully insert the headlight assembly back into place. 5) Replace the three screws removed in step 2 being carefull not to over tighten.