To reset the service light on a 2009 Volvo S80 with a push start, first, turn the ignition to the "On" position without starting the engine. Press the "Trip" button on the instrument cluster until you see the "Service" message, then press and hold the "Trip" button for about 10 seconds until the message disappears. Finally, turn off the ignition and then start the engine to ensure the service light has been reset.
To reset your service light here are the steps. 1. Get in your car and shut the door. 2. Put your key in the ignition 3. Turn your ignition key to position 1 4. Push in your Odometer reset button and hold it in while holding it move the ignition key to position 2 while holding down the odometer reset button. 5. After couple of seconds of holding the button down and the key in position 2 your service light will start to blink once that happens let go of the reset button and start the car. This should reset your service light and a service light on your Volvo C/S/V70 cars from 1999 onwards.
Turn key to accessory position. Press and hold trip meter reset button. Wait half a second and turn key to on position (not start) continuing to hold trip button. After a few seconds the service light will start flashing. At this point release the trip button, cycle the key and start the engine. The service light should be reset.
To reset your service light here are the steps. 1. Get in your car and shut the door. 2. Put your key in the ignition 3. Turn your ignition key to position 1 4. Push in your Odometer reset button and hold it in while holding it move the ignition key to position 2 while holding down the odometer reset button. 5. After couple of seconds of holding the button down and the key in position 2 your service light will start to blink once that happens let go of the reset button and start the car. This should reset your service light and a service light on your Volvo C/S/V70 cars from 1999 onwards.
turn key 1 click keep your finger on milage reset button turn key another click do not start the car when the service light starts flashing take your finger off the button switch car off and the service light should stay off
To reset the service CCR light on a 1991 Eldorado, disconnect the battery for 10 minutes. Reconnect it and start the car.
To clear the service light on a 1998 Volvo S70, turn the ignition key to the "II" position without starting the engine. Press the gas pedal all the way down three times within five seconds. Turn the ignition off, then start the engine to check if the service light has reset. If it remains on, the procedure may need to be repeated or further diagnostics may be required.
it is due a service and the garage can reset the light
To reset the maintenance light on a 2002 Volvo V40, start by turning the ignition key to the "II" position without starting the engine. Press and hold the trip odometer reset button on the dashboard. While holding the button, turn the ignition off and then back to the "II" position again. Release the button, and the maintenance light should be reset.
To reset the ABS warning light on a Volvo V70 2.4, start by ensuring that the vehicle is in a safe location and turned off. Disconnect the negative terminal of the battery for about 10-15 minutes to reset the system. Reconnect the battery, then start the car and check if the warning light has turned off. If the light persists, it may indicate an underlying issue that requires diagnostic tools or professional assistance.
Don't know how to reset, but I'm pretty sure that if you did succeed, every time you start the car it will perform a systems check and recognize the problem and just keep throwing the warning until the problem is fixed.
you simply get in car with door shut, turn key to "dash lights on position", hold odometer reset button in, then turn key to full ON position"headlights on" and hold for 3-5 seconds. light should be flashing. turn off then start car--done.
To reset the service light on a 2006 Mitsubishi L200, turn the ignition to the "ON" position without starting the engine. Press the accelerator pedal three times within 10 seconds. After that, turn the ignition off and then start the engine to ensure the service light has reset. If the light remains on, repeat the process to confirm.